A square footing is to be used to support a 300mm by 300mm RC column loaded with 500 kN dead load and 230 kN live load. If the net allowable bearing capacity is 330 kPa, determine the size of the footing. Determine also the minimum thickness based on one way shear and two way shear. Use f'c = 21 MPa and fy = 345 MPa. Use d = t - cc - 1.5db.

A square footing is to be used to support a 300mm by 300mm RC column loaded with 500 kN dead load and 230 kN live load. If the net allowable bearing capacity is 330 kPa, determine the size of the footing. Determine also the minimum thickness based on one way shear and two way shear. Use f'c = 21 MPa and fy = 345 MPa. Use d = t - cc - 1.5db.

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter11: Load And Resistance Factor Design (lrfd)

Section: Chapter Questions

Problem 11.1P: A continuous foundation is required in a soil where c=10kN/m2, =26, and =19.0kN/m3. The depth of the...

See similar textbooks

Similar questions

Design a square pad footing with an overall depth of 600mm, cover to the reinforcements 50mm with 20mm diameter reinforcement bars in both directions. The footing carries a 400mm square column with a dead load of 1050KN and imposed load of 300KN. The safe bearing capacity of the soil is 170KN/m^2, fcu 30N/mm^2. Assume a unit weight of concrete to be 24KN/m^3 and footing weight 150KN
A continuous foundation is required in a soil where c=10kN/m2, =26, and =19.0kN/m3. The depth of the footing will be 1.0 m. The dead load and the live load are 600 kN/m and 400 kN/m, respectively. Determine the required width for the foundation based on allowable stress design with FS = 3, using Eq. (6.10) and Table 6.1.
A square footing is to be used to support a 300mm by 300mm RC column loaded with 500 kN dead load and 230 kN live load. If the net allowable bearing capacity is 330 kPa, determine the size of the footing. Determine also the minimum thickness based on one way shear and two way shear. Use f'c = 21 MPa and fy = 345 MPa. Use d = t - cc - 1.5db. %3D
QUESTION 3 A footing of size 2.5 m x 2.5 m and 450 mm thick resists characteristics axial loads of 500KN dead and 200 kN imposed from a 300mm square column. The safe bearing pressure on the soil is 230kN/m?. a. Check whether the base pressure is safe b. Design the bending reinforcement, assuming 16mm diameter bars c. Check the punching shear Further Design Information Characteristic strength of concrete (fm) = 35 N/mm? %3D Characteristic yield stress of steel (f;) 460 N/mm2 Cover to reinforcement = 75 mm Diameter of main bars = 16 mm Unit weight of concrete = 24 kN/m³
Given the following:Column: 600 mm x 600 mmAxial Dead Load = 1680 kNAxial Live Load = 1350 kNDepth of footing = 1.8 mAllowable soil pressure = 230 kPaUnit weight of soil above footing = 16 kN/m 3Unit weight of concrete = 24 kN/m 3fc' = 28 MPafy = 345 MPaDesign the footing if its width is limited to 3.2 m. Use 25 mm bars and 75 mm clear concrete cover. Useload factor of 1.4 DL + 1.7 LL.
A column 500 mm x 500 mm square is supported by a 3.5 m x 3.5 m isolated spread footing. The column carries a dead load of 1200 kN and a live load of 1000 kN. The total depth of the footing is 550 mm with steel cover of 100 mm. Use NSCP 2001 provisions. Determine the punching shear stress at ultimate loads. A 1830.00 kPa 2154.11 kPa 1566.48 kPa D 1331.52 kPa
A 5 * 7 ft footing is founded at a depth of 2 ft and supports a vertical load of 80 k and a moment load of 30 ft-k in the B direction and 50 ft-k in the L direction. Determine the dimen-sions of the equivalent uniformly loaded footing and compute the equivalent bearing pressure.
A 500 mm square concrete column carries factored ultimate column loads of PU = 580 kN andMU = 30 kN@m. The vertical service load is 490 kN. It is to be supported on a square footingwith f′c = 20 MPa and fy = 420 MPa. The soil has an allowable bearing pressure for bearingcapacity of 650 kPa (based on LRFD methods) and an allowable bearing stress for settlementof 280 kPa. The groundwater table is at a great depth. Determine the required footing, width,thickness, size of the flexural reinforcement, and show your design in a sketch.
A square footing 2.5m x 2.5 m supports a square column 300mm x 300mm at its center. Concrete cover to bar centroid = 100mm. Ultimate load combination is 1.2DL + 1.6L. Column loads aee service conditions:DL = 680 kN LL = 400kNf'c = 20.7 Mpa fy = 275 MPa Calculate the nominal punching-shear stress acting at the critical section of the footing slab if the thickness of the slab is 450 mm. (Correct Answer 1.99)
A square footing 2.5m x 2.5 m supports a square column 300mm x 300mm at its center. Concrete cover to bar centroid = 100mm. Ultimate load combination is 1.2DL + 1.6L. Column loads aee service conditions: DL= 680 KN LL = 400KN f'c = 20.7 Mpa fy = 275 MPa Calculate the nominal punching-shear stress acting at the critical section of the footing slab if the thickness of the slab is 450 mm.
A footing supporting a 2 ft x 2 ft column load carring 550 kips (dead load) and 200 kips (live load). The foundation level is 5 ft below the ground surface. The gross allowable bearing capacity is 6 ksf. The unit of soil is 130 pcf. You are required to provide complete design calculations for bearing, shear, and flexure for the strip footing. Assume f' = 4 ksi, fy = 60 ksi.
pls answer