A square flat plate with a side length of 0.65 m is maintained at Tw 100°C. The plate is exposed to a convection environment at 30°C. An applicable correlation is Nu-Pr¹/3 (0.037Re0.8 - 871) eqn. (5-85) when the condition of flow gives Re=7 x 105 and the Pr = 0.708. If the thermal conductivity of the convection fluid is 0.03 W/m K. what is the rate of heat transfer given up by the plate? Express your answer in Wattts.

A square flat plate with a side length of 0.65 m is maintained at Tw 100°C. The plate is exposed to a convection environment at 30°C. An applicable correlation is Nu-Pr¹/3 (0.037Re0.8 - 871) eqn. (5-85) when the condition of flow gives Re=7 x 105 and the Pr = 0.708. If the thermal conductivity of the convection fluid is 0.03 W/m K. what is the rate of heat transfer given up by the plate? Express your answer in Wattts.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.31P

See similar textbooks

Similar questions

onyl attempt once
Assume that the head can be modeled as a hemisphere (radius ro 90 mm) with a single layer of brain tissue (k-0.5 W/m °C). The bottom of the hemisphere is insulated. The head surface is assumed exposed to a convection environment (h-8 W/m²K, T-25°C). Based on the boundary conditions, the brain tissue temperature can be treated as 1-D, i.e., T.(r), where r is the radial variable in the spherical coordinates. The volumetric metabolic heat generation rate in the brain is uniformly distributed and is equal to q=10000 W/m³. Consider two situations, a) no blood perfusion is considered; b) blood perfusion rate is uniform in the brain and is equal to @=0.01 s¹. The governing equation (steady state, 1-D heat transfer in the spherical coordinate system, with or without the Pennes perfusion term) and boundary conditions for both situations can be written as: k₁ 1 d 2 r=0 dr dT, dr dT, 17/17) + 0 dr =0 T,(r)= dT, r=r-k₁- =h(T, -T.) dr (a) For the first situation without considering blood perfusion…
A:Find the amount of heat transferred through an iron fin of thickness 5 mm, length 10 cm and width 100 cm. Also determine the temperature difference e at the tip of the fin at: 1- adiabatic tip, 2-heat convection at the tip. Assuming the atmospheric temperature of 28°C K=50 w/mK, h=10 w/m’K, O,=80°C. B-Why is the dimensional heat flow assumption important in the analysis of fins problems? C- Why are the annular fins more efficiency than others?.
Since the correlation given in the textbook is so complicated, Dr. Roy wants to come up with a new correlation for convection over a sphere. He proposes the correlation to be NUD D=2+C Re" Pr3 He used a steel sphere (conductivity of 42 W/m-K) of 20 cm diameter that generates steady 40 W heat. He placed it in air flow with 1 m/s where air temperature is 20°C. He then measured the steady state tempera- ture of the sphere surface to be 30°C. 31'8 w/m² K Based on his measurements, what is the convection coefficient? Using properties at film temperature, what should the value of C be as per Dr. Roy's calculations if he assumes m = 0.8? O'142 What is the temperature at the center of the sphere? 30 38 C
What’s the correct answer for this please ?
Heat mass transfer
Q4/The outside wall of a building 6 m high receives an average radiant heat flux from the sun of 1100 W/m². Assuming that 95 W/m² is conducted through the wall, estimate the outside wall temperature. Assume the atmospheric air on the outside of the building is at 20°C. Ans. 170°C
A steel plate of thermal conductivity 50 W/mK and thickness 10 cm passes a heat flux of 30 kW/m2 by con- duction if the temperature of the hot surface is 100°C then what is the temperature of the cooler side of the plate (A) 40°C (С) 60°C (В) 50°C (D) 70°C
A single-phase fluid reservoir is described by four equal blocks as. The reservoir is horizontal and has homogeneous and isotropic rock properties. k-270 md and -0.27. The gridblock dimensions are Ax-300 ft. Ay-350 ft, and h 40 ft. The reservoir fluid properties are B-B-1 RB/STB, p-50 lbm/ft, and μ-0.5 cP. The reservoir left boundary is kept at constant pressure of 4000 psia, and the reservoir right boundary is sealed off to flow. A 7-in vertical well was drilled at the center of gridblock 4. The well produces 600STB/D of fluid and has a skin factor of 1.5. Assuming that the reservoir rock and fluid are incompressible, find the pressure distribution in the reservoir and the FBHP of the well. Perform a material balance check.
What’s the correct answer for this please ?
J 6 A semi-infinite solid, with a boundary condition of convection on the surface (Tfluid = 100°, h = 220 W/m2-°C) has at t=0s, a uniform temperature of Ti = 0°C, draw the isotherm of 60°C, at time t = 2h. Consider the solid to be cast iron.
A Deep-sea Diver is wearing a wetsuit in cold water. (Natural convection, radiative transfer is negligible). The following data are given: Water Temperature Te= 10 Degrees Celsius. Wetsuit thickness is equivalent to a 8mm neoprene rubber (thermal conductivity is 0.19 W/m-K), Skin thickness is 1.45mm, Skin thermal conductivity is 0.21 W/m-k. Body temperature below skin Tb= 37 degrees Celsius. Average Air gap thickness is 1mm, air thermal conductivity = 0.027 w/m-K. a) Draw a complete equivalent thermal circuit and show all parameters. b) Calculate the flux of heat loss from the diver (in W/m^2 of body surface area) c) Calculate the temperature of the skin outer surface (Ts) d) Based on your calculations is the wetsuit adequate to keep the diver warm enough? Why?