Answered: A spring subjected to a compressive…

A spring subjected to a compressive force of 20kN with a spring constant k = 100 k/m. If the shortening of spring is 0.2 m. compute the work done in the spring.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.9P: A safety valve on the top of a tank containing steam under pressure p has a discharge hole of...

See similar textbooks

Related questions

Q: 4. A symmetric body moves without the influence of forces or torques. Let x, be the symmetric axis…

A: L1=0=I1ω1L2=Lsinθ=I1ω2=I1ωsinαL2=Lcosθ=I3ω3=I3ωcosαtanθ=L2L3=I1I3tanα ............... 1 We know,…

Q: The bottom of a 50mm diameter, 2mm thick metallic induction heater is 120C while its thermal…

Q: Pl-3. Determine the largest internal normal force in the bar. D 10 kN 5 kN 2 kN 6 kN

A: To find the largest internal normal force.

Q: Two equal gear wheel of 360 mm p.c.d and 6 module are in mesh if the pressure angle 20 determine the…

Q: A plastic beam has a cross section with dimensions of a = 4.7 in., b = 16.5 in., d = 9.4 in., and t…

Q: The box slides down the helical ramp which is defined by r = 0.5 m, θ = (0.5t^3) rad, and z = (2 -…

Q: 3. The bottom of a 50mm diameter, 2mm thick metallic induction heater is 120C while its thermal…

Q: X(s) from the following block diagram. F(s) Obtain the transfer function F(s) + X(s) S 5 9 A) s – 6…

Q: 5. A 5.6 liter V10 compression-ignition truck engine operates on a four stroke cycle at 3600 rpm…

Q: Two block m1 = 20 kg and m2 = ID kg , shown in the figure. Calculate the value of friction factor…

Q: 500 MPa 400 MPa 250 MPa 150 MPa 0,00075|0.02 0.2 0,25 0.28 0.0013 1 1:1

A: The most crucial information when studying solids and their mechanical characteristics is…

Q: How are you getting 16 mm at the end for an answer , "HX83=219X10^3/164.909".................is…

A: Stress, σ = FA F = 219 kNσ = 164909 kPa Substituting the values 164.909=219AA = 0.001132 m2 One…

Q: For the plan area shown in the figure, determine the location of the centroid of the shaded area.…

A: Consider the section as shown below,

Q: 1. A pair of spur gears is to be selected for a drivetrain. The pinion is labeled 2, and the gear is…

Q: The lap joint is fastened with four 0.65-in.-diameter rivets. The working stress is 20.72 ksi for…

Q: For the machine element shown, locate the z coordinate of the center of gravity.

A: Consider the volumetric section as shown below,

Q: Explain the functions and provide visual presentation of the following auxiliary machinery

A: A boiler, a steam turbine and generator, as well as additional auxiliaries, make up a steam power…

Q: Find the design calculations of the gears box ,has (3)three speeds, Which is transmitted the power…

A: Given Data: The number of the tooth in gears are Z1=8, Z2=32 and Z3=64. The speed of 8 tooth gear…

Q: PROBLEM: VIE-23 BOOK: ENGINEERING THERMOFLUIDS, M. MASSOUD (You can answer my question even if…

A: The masses of the proton and the neutron are approximately equal. Thus, when the mass of one of…

Q: The jet plane travels along the vertical parabolic path. When it is at point A it has a speed of 200…

Q: a) Determine the internal forces acting at s b) Determine the stress components that ac =…

A: INA=2.6525×10-7m4 To-Find:- a) The internal forces acting at section a-ab) The stress components…

Q: Locate the centroid of the plane area shown. 30 mm 300 mm 30 mm 240 mm X = 175.6 mm, Y = 84.4 mm X=…

Q: Engr. Mercado wishes to replace a solid transmission shaft 4.2 inches with a hollow shaft of same…

Q: Determine the horizontal and vertical reactions at the connections A and C of the gable frame.…

A: For the given configuration, it is required to determine the vertical and horizontal reactions at A…

Q: Explain the principles of metal rolling in not more than 10 sentences

A: Rolling is a metal forming process that involves passing metal stock between one or more pairs…

Q: TOC) P(kPa) u(kJ/kg) Phase description 175 2524.5 325 4000 325 Saturated liquid

A: Given: P= 175 kPa u= 2524.5 kJ/kg Note: Use APPENDIX 1 (PROPERTY TABLES AND CHARTS (SI UNITS))…

Q: Problem 2.1: The double pulley consists of two parts that are attached to one another. It has a…

Q: A 4000-N tractor is used to lift F N of gravel. i-Determine the reaction at each of the two rear…

A: Given:Weight of the tractor, W=4000 NGravel weight, F=388 N

Q: e characteristic polynomial method. 6 2

Q: Pl-3. Determine the largest internal normal force in the bar. F D A 10 kN 5 kN 2 kN 6 kN P1-3

Q: I50,000 CS 10,000s aasooo000O + 290 cs +41850000 t ISO,000 +aasoooo0oc the damping eta = 0.707 value…

Q: In a conventional refrigeration cycle which uses Freon-12 as the refrigerant, the temperature of the…

Q: A chair lift is to be installed from the surface down to a depth of 150 m. The inclination is 17…

Q: Four forces F1, F2, F3 and F4 are being applied on a plate as shown in Figure 1. If your roll number…

A: Assume A, B, C, D are points where F1, F2, F3 and F4 act respectively

Q: The constant wall thickness of a tube with the elliptical cross section shown is 0.12 in. what…

A: As per given Question Wall thickness =0.12in Shear force =6000 psi We have to determine the torque

Q: In a Series and parallel pumps, How to operate pumps in series and parallel? Explain briefly…

A: When a number of pumps are in parallel, the overall pump provides the net head equal to the head of…

Q: Q2/ Compute the burst-pressure rating for 10.75-in., J-55 casing having a nominal wall thickness of…

A: The burst pressure rating is 3581.4 psi.

Q: Question 5: A model for a single joint of a robotic manipulator is shown in Figure below. The usual…

A: The system of equation are The change of variables are The values of the parameters are k=0.5 N/m;…

Q: Determine the normal force, shear force, and bending moment at point C. 3 kip/ft B C 6 ft +4.5 ft…

Q: A small aluminum alloy [E = 71 GPa] tee shape is used as a simply supported beam as shown. For this…

Q: Make a concrete example of a linear dynamical system that observes a stable equilibrium, unstable…

A: Dynamical systems are mathematical objects that are used to represent physical processes that…

Q: Calculate the value of the viscosity coefficient and its propagated error where ( slope 22…

A: The coefficient of viscosity ηηs=ρsVWhere-V=S10pe=122 cm-1.s-1ηs=7.86×122ηs=958.92 poise

Q: Lecture 6: Balanced Delta Load IBR VeN VRY BR 21.8 IRY 82,V -21.8 IYB VYB.

A: The voltages in the three-stage power framework are delivered by a simultaneous generator . In a…

Q: Please handwriting make the solution very simple not long 3. [Ch7 – 2] For the first-, second-, and…

A: given details

Q: shown if i llov and th

Q: Which equation below calculate the surface speed of a milling cutter.

A: Question: Which equation below calculate the surface speed of milling cutter.

Q: Three plates are welded together to form the section shown. Dimensions of the cross section are b =…

A: For the given welded joint it is required to determine the shear flow through the welded surface at…

Q: 5.29 Determine the specific speed of the following centrifugal pumps: (a) A single-stage pump…

A: Given:a) N=1450 rpmH=12.8 mQ=15 L/s =15*10-3 m3/sb) n=2N=1450 rpmH=24 mQ=25 m3/h =0.0069444 m3/s

Q: Problem-based learning - Acquire enhanced problem-solving skills using critical thinking Two shaft…

A: Given data: The diameter of the shafts is d = 35 mm The number of bolts is n = 8The diameter of the…

Q: The fluid in a tank receives 50 kJ of heat while a shaft delivers 10 kJ of work. The heat loss from…

A: Given Heat supplied, QS = 50 kJ Heat rejected, QR = 20 kJ Shaft work, w = 10 kJ Initial…

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

A spring subjected to a compressive force of 20kN with a spring constant k = 100 k/m. If the shortening of spring is 0.2 m. compute the work done in the spring.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. Determine the possible range for R is the equivalent spring stiffness constant varies from 50 N/m to 500 N/m 15 KN/m ww Anwer: 20 points 750 N/m
Find the spring constant if a 20. N force stretches a spring 2.0 m.
Considering the figure shown, determine the equivalent spring constant of a spring that will represent all of the given springs such that its deflection is along a vertical path with the mass. k1=1N/m k2=2N/m k3=3N/m k4=4N/m and k5=5N/m. (answer in N/m) * k2 m kg k4
Given values: m1 = 10kg, r1=75 cm, m3=20kg, r3=25cm, m4=5kg, had to find the value of r4=? I got r4=50cm m1 = 10 kg at r1 = 75cm m3 = 20 kg at r3 = 25cm m4 = 5 kg at r4 = 50cm 1. Compute the theoretical value of r3 using the following equation: r1m1 = r3m3 + r4m4 2. Compute the % error of r3 using the following equation: % error = |theoretical value - experimental value| / theoretical value x 100%
Considering the figure shown, determine the equivalent spring constant of a spring that will represent all of the given springs such that its deflection is along a vertical path with the mass. k1=1N/m k2=2N/m k3=3N/m k4=4N/m and k5=5N/m. (answer in N/m) * k2 m k3 k5 k4
A truck of mass 3 tonnes runs into a buffer stop having three buffer springs each of 40 kN/cm stiffness connected in parallel. Find the maximum compression of the springs, and the load if the wagon is travelling at 60 kmph. 1-Equivalent Stiffness of spring in kN/mm is 2-Kinetic Energy in kNmm is 3-The maximum compression of the spring in mm is 4-Load acting on the spring in kN is
CDEFGH is plate with a circular hole in it and has a unit weight p = 2 kN/m². If the initial length of the spring is 1m, find the stretched length of the spring attached at C to the given system. The stiffness of the spring id k-50 kN/m. p H 0 2 m Lütfen birini seçin: D A. 1.6019 m B. 1.8258 m C. 2.0480 m D. 2.2694 m E. 1.3727 m F. None of the above X 2 m 2 m G 2 m F E 3m 1m
In the graph the force versus displacement of a spring is given (the spring is shown in a separate figure--see below). The x-axis range is ±2 cm. The y-axis range is tFs, where Fs = 220 N. How much work does the spring do on the block (the mass "m") when the block moves from x₁ = 7.6 cm to 4.3 cm? W J y F. X -1.5 -0.5 0 10.5 1 1.5 -F How much work does the spring do on the block (the mass "m") when the block moves from x; = 7.6 cm to -7.6 cm? W = Question Help: Read Submit Question m
A truck of mass 1 tonnes runs into a buffer stop having three buffer springs each of 15 kN/cm stiffness connected in parallel. Find the maximum compression of the springs, and the load if the wagon is travelling at 110 kmph. Equivalent Stiffness of spring in kN/mm is Kinetic Energy in kNmm The maximum compression of the spring in mm Load acting on the spring in kN is
The mass of the block is mc=41 kg and the angle a=33deg. mc What is the tension in the cable D, TD in N. Give your answer as an integer.
In the given fig shows the suspension system of a freight truck with a parallel-spring arrangement. Find the equivalent spring constant of the suspension if each of the three helical springs is made of steel with a shear modulus G = 120GPaand has five effective turns, mean coil diameter D = 50 cm, and wire diameter d = 5 cm
QI/ The sphere E has a mass of ( 6 kg ) and is supported as shown in figure bellow, A) determine the force in spring CD,B) determine the change in length in spring CD if it has a stiffness of k = 300 N/m (specify if the change in length is elongation or shortening). *