A spherical gas-storage tank with an inside diameter of 26 ft is being constructed to store gas under an internal pressure of 210 psi. The tank will be constructed from structural steel that has a yield strength of 33 ksi. If a factor of safety of 3.0 with respect to the yield strength is required, determine the minimum wall thickness required for the spherical tank.

A spherical gas-storage tank with an inside diameter of 26 ft is being constructed to store gas under an internal pressure of 210 psi. The tank will be constructed from structural steel that has a yield strength of 33 ksi. If a factor of safety of 3.0 with respect to the yield strength is required, determine the minimum wall thickness required for the spherical tank.

Solid Waste Engineering

3rd Edition

ISBN:9781305635203

Author:Worrell, William A.

Publisher:Worrell, William A.

Chapter5: Separation Processes

Section: Chapter Questions

Problem 5.32P

See similar textbooks

Similar questions

strength of material subject columns chapter about reduction factor, in working stress
Please show your solution on a paper with FBD
A spherical gas-storage tank with an inside diameter of 29 ft is being constructed to store gas under an internal pressure of 218 psi. The tank will be constructed from structural steel that has a yield strength of 38 ksi. If a factor of safety of 3.0 with respect to the yield strength is required, determine the minimum wall thickness required for the spherical tank.
Q17 Please provide justified answer asap
For the 150mm hollow concrete vertical cell unit, the most common type is I. Select one: O True O False The standard acceptable modulus of rupture of partially-grouted hollow unit walls in running bond with type M joint mortar in MPa is? а. 17.2 O b. 6.9 О с. 12 d. 8 e. 0.69 Clear my choice
pls ans soon
Question 1: Consider a 600 mm deep reinforced concrete cantilever beam supported by a 600 mm square column as shown in the figure below. The beam reinforcement is anchored into the column. Minimum stirrups are provided in the anchorage zone according to CSA A23.3-19. Regular uncoated bars are used in the design. Material properties: fe= 35 MPa (normal-density concrete) and fy= 400 MPa. 1. Determine the largest beam rebar size that can be used without hook in this design according to the CSA A23.3 requirements. 2. Design the anchorage zone if the diameter of the longitudinal steel bars is 25 mm. 40 clear- 600 mm 40 clear 600 mm,
Q2. Caleculate the CBR value for the laboratory data in the table. Load (kn) Mold Mold Mold 3 Penetration (mm) 2 2.5 0.7 1.3 2.2 5.0 1.13 1.7 2.9
2) The flooring system shown is composed of slab panels measuring 20 X 25 ft in plan, supported by shallow column-line beams, as shown in the figure. The slab is pre-cast and resting on the beams. The panels carry a service live load of 144 psf in addition to the self-weight of the floor. a) Calculate the factored load on beam CD as per the tributary area shown. Assume a slab thickness of 7 in and the density of the concrete used to be 150 pcf. Use the load combinations from the ASCE 7-10 load combinations for Strength Design (2.3.2). b) Sketch the bending moment diagram (BMD) for the beam using the factored load calculated in step (a). c) Calculate Mu for the trapezoidal load distribution. d) Design a reinforced concrete beam using a rectangular section to carry the Mu calculated in step (c). You can use design guides, but show clear steps. Use concrete with fc'=4000 psi and steel with fy = 60000 psi.
Qualifying materials Quantify the materials that you used in your drum (acoustic treatment only) Sample No. Description. Quantify. Unit ¹. Rockwall insulation 1. Roll
Need help asap pls.
Q-civil Concrete formwork Ata temperature of 50°F, 150 lb per cu ft of concrete is poured into a 14-foot-tall column form. Since there is no retarder, the concrete is Type I. Concrete will be poured to a depth of less than 4 feet with typical internal vibration. The placement speed is 7 feet per hour.