A VERTICAL CYLINDRICAL STEEL STORAGE TANK HAS 30 M DIAMETER AND THE SAME IS FILLED UPTO A DEPTH OF 15 M WITH THE GASOLINE OF RELATIVE DENSITY 0.74. IF THE YIELD STRESS FOR STEEL IS 250 MPA, FIND THE THICKNESS REQUIRED FOR THE WALL PLATE. ADOPT A FACTOR OF SAFETY OF 2.5 AND NEGLECT LOCALIZED BENDING EFFECTS, IF ANY

A VERTICAL CYLINDRICAL STEEL STORAGE TANK HAS 30 M DIAMETER AND THE SAME IS FILLED UPTO A DEPTH OF 15 M WITH THE GASOLINE OF RELATIVE DENSITY 0.74. IF THE YIELD STRESS FOR STEEL IS 250 MPA, FIND THE THICKNESS REQUIRED FOR THE WALL PLATE. ADOPT A FACTOR OF SAFETY OF 2.5 AND NEGLECT LOCALIZED BENDING EFFECTS, IF ANY

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A load of 1950N is raised at the end of a steel wire. The minimum diameter of the wire so that…

A: Given data :- Load = 1950 N Stress = 100 N/mm2 Calculate the minimum diameter of the wire

Q: A transmission shaft made of steel having ultimate strength 500 MPa and yield strength 320 MP is…

A: Given data : Ultimate strength of steel shaft = 500 MPa Yield Strength = 320 MPa Endurance strength…

Q: A thin-wall tube, made of a unidirectional graphite/epoxy lamina with a fiber direction 0 to its…

Q: For the beam geometry shown, determine the following: a. Cracking moment b. Has the beam section…

A: Given Mapp = Applied moment = 34KN .mfc'=Concrete strength=28MPaAs=Area of steel=1935m*m2n=Modular…

Q: A rigid beam ABCD is supported by a pin at B and two cables lócated at A and C. The cables have a 30…

A: Solution “Since you have asked multiple questions, we will solve the first question for you. If you…

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

A VERTICAL OYLINDRICAL STEEL STORAGE TANK
HAS 30 M DIAMETER AND THE SAME IS FILLED UPTO
A DEPTH OF 15 M WITH THE GASOLINE OF RELATIVE
DENSITY 0.74. IF THE YIELD STRESS FOR STEEL IS 250
MPA, FIND THE THICKNESS REQUIRED FOR THE WALL
PLATE, ADOPT A FACTOR OF SAFETY OF 2.5 AND
NEGLECT LOCALIZED BENDING EFFECTS, IF ANY

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The point loads are placed at the fixed positions shown in the figure and they are live loads. A k a b a b dn = 1₂ Icr= M B 7 Ast Stress profile (concrete) Cross section before cracking Aso Cross section Asc Ast N.A. Q2) Now, the live load increases gradually and the moment at the critical section just exceeds the cracking moment (Mcr), but the compressive section of the concrete is still under the linear elastic region. Please be reminded that in the flexural design, the crack of the concrete section starts where the tensile stress reaches the tensile strength. It is assumed that the cracks then propagate rapidly up to the entire tension section (up to the neutral axis) and this cracked concrete section cannot resist the tension. It should be noted that in reality, concrete sections between the primary cracks can still resist some tensile stresses as shown in the figure, which should be considered in the displacement design. However, in flexure design, we design the critical section…
Consider the compound system consisting of three sections with cross-sectional areas 3A, 2A, and A and loaded as shown. Which of the following gives the maximum average normal stress in the system shown? 6P 4P A5.5 P/A B.4.5 P/A 3A 2A A 3P C.4 P/A D.3 P/A 4P 6P Which of the following is the highest value of stress within the strain hardening region of a typical elasto-plastic material subjected to tensile test? A. Elastic Limit B.Yield Stress C.Ultimate Stress D.Proportional Limit What is the lateral strain of a uniaxially loaded member if its longitudinal strain is 0.02 and its Poisson's ratio is equal to 0.3? A.+0.006 B.-0.006 C.+0.667 D.-0.667 Which of the following is the highest value of stress within the elastic region of a typical elasto-plastic material subjected to tensile test? A.Yield Stress B.Elastic Limit C.Ultimate Stress D.Proportional Limit
A flat annular steel disc of 0.8 m outside diameter and 0.15 m inner diameter is to be shrunk around a solid steel shaft. The shrinking allowance is 1 part per 1000. Neglecting shaft expansion, determine: (a) The stress in the system at standstill. (b) The speed at which the shrink fit will loosen as a result of rotation. Material density is 7800 kg/m³; Poisson's ratio is 0.3; Young's Modulus is 210 GPa; [108.68 MPa: 4300 rpm
A 42 meter solid shaft is under torsional loading 53 Nm. If in this application, the allowable shear stress for the material is 369 MPa. Calculate the required minimum diameter of the shaft: _____ mm ( input the value directly from your calculation before rounding it up to an engineering accepted diameter) Pay attention to units, and calculate your answer to one decimal place.
The plastic modulus of a section is 5 x 10-4 m³. Its shape factor is 1.2 and the plastic moment capacity is 120 kNm, what is the value of the yield stress of the material?
solve thee following problem with the correct answer please, please make sure to show so I can understand.
Show solution and box final answer pls ty
Mechanics of deformable bodies.
The concrete beam shown below is made of an all-lightweight concrete with a unit weight 7=/ 800 kg/ ni a. Compute the value of the cracking moment and b. Estimate the value of the concentrated load P at midspan that causes the beam to crack (include the dead weight of the beam). f, =27.5 MPa 100 mm P=? Wbeam 2-D25 - 5 m 100 mm 100 mm 300 mm