A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10 kW, (2) an induction motor drawing 10 kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10 hp, 85% efficiency and 0.95 power factor leading (1 hp 0.746 kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.

A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10 kW, (2) an induction motor drawing 10 kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10 hp, 85% efficiency and 0.95 power factor leading (1 hp 0.746 kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need help with this homework question.
Problem #7) Specify whether each of the statements are TRUE or FALSE. D Reactive Power is a measure of the average power consumed by reactive (capacitive and inductive) loads. When connected to an AC voltage source, the instantaneous power (rate of energy transfer) supplied to a resistor varies at a frequency that is 2x the frequency of the applied source voltage. The magnitude of the impedance of a capacitor supplied by an AC source will increase as the source frequency increases. An AC source that has an RMS magnitude of 100V will supply the same average power to a resistor compared to a 100V DC source. The voltage across a capacitor is proportional to the rate of change of the current flowing through the capacitor. The magnitude of the impedance of a resistor supplied by an AC source does not vary as the source frequency increases. A complex impedance Z=R+jX, that has non-zero resistive and reactive components, will consume both real and reactive power when supplied by an AC source.…
1) Determine the total current supplied by the source and the current in each branch. 2) Sketch a fully labelled phasor diagram showing all voltage and currents in the circuit. 3) Determine the active power delivered by the source voltage. 4) Determine the reactive power. 5) Sketch the power triangle. 6) Comment on the significance of the power factor and briefly state how it can be improved.
answer C and E only
2. A voltage applied to a load is V=208 4 20°V and current through load is I=10 a–10° A. Find the following [SO 1] o complex power consumed by load o Is the load inductive or capacitive? o the power factor of the load o the reactive power consumed or generated by the load. o Does the load consume or supply reactive power?
For the following voltage and current phasors, calculate the complex power, apparent power, real power, and reactive power. Determine whether the power factor is leading or lagging. V = 300/30° V rms, I = 0.5/60° A rms The value of apparent power is The value of real power is The value of reactive power is The power factor is (Click to select) ✓ W. VA. VAR.
Two loads are connected in parallel to a 2000 V(rms) 50Hz source. one of the loads Each of them has 500KVAR reactive power and 0.6 reverse power factor. Other load 300KW since it has absorbing power and 100KVAR dissipating power a) Draw the equivalent circuit of the system b) Find the common power factor of the system c) In order for the power factor to be 0.98 back, the capacitor to be connected in parallel with the loads find its value d) The magnitude of the current drawn from the source is measured before and after the capacitor is connected Find and compare for the next cases. Not. Solve this question in detail step by step and explain your requests in detail
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of158 volts, 50 Hz supplies the combination. Determine the following: e. Reactive power supplied by the sourcef. Apparent power of the circuitg. Power factor of the entire circuit
A load is supplied by a 230 V, 50 Hz source. The active power P and the reactive power Q consumed by the load are such that 1 kW SPS2 kW and 1 KVAR SQS2 KVAR. A capacitor connected across the load for power factor correction generates 1 KVAR reactive power. The worst case power factor after power factor connection is Options: 1. 0.447 lag 2. 0.707 lag 3. 0.894 lag 4.1
Problem 1 • A sinusoidal source with frequency of 60 Hz and rms-voltage of 100 V is connected to an RL load of 10 ohms and 100 uH. Find Power Factor From Calculation Find Power Factor From Plot L=10mH find power factor from calculation only
Consider the situation shown in (Figure 1). A 1000-V-rms source delivers power to a load. The load consumes 140 kW with a power factor of 55 percent lagging. Time remaining: 00:07:30 Electrical Engineering Consider the situation shown in (Figure 1). A 1000-V-rms source delivers power to a load. The load consumes 140 kW with a power factor of 55 percent lagging. 1- Find the phasor II, assuming that the capacitor is not connected to the circuit. Enter your answer using polar notation. Express argument in degrees. 2-Find the value of the capacitance that must be connected in parallel with the load to achieve a power factor of 100 percent. Express your answer to three significant figures and include the appropriate units. 3-Usually, power-systems engineers rate capacitances used for power-factor correction in terms of their reactive power rating. What is the rating of this capacitance in kVAR? Express your answer using three significant figures. 4-Assuming that this…