A solid steel shaft will not twist through more than 3° in a 6.0 m length when subjected to a torque of 12 kN-m. What maximum shearing stress is developed? Use G = 83 GPa. A )43.88 MPa B) 40.89 MPa 42.11 MPa )41.27 MPa

A solid steel shaft will not twist through more than 3° in a 6.0 m length when subjected to a torque of 12 kN-m. What maximum shearing stress is developed? Use G = 83 GPa. A )43.88 MPa B) 40.89 MPa 42.11 MPa )41.27 MPa

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Related questions

Q: 1. A mass is supported by the cable system shown below. If the tension in cable A is 14 kN, find the…

A: Tension in cable A: TA = 14 kN = 14000 N Cable attached to mass "m" composed of aluminium alloy:…

Q: D 10 cm 30° M C B 20 cm Quest The allowable tension and compression stresses are given as: gtension…

Q: The wood beam has an allowable shear stress of Tallow = 5 MPa. (Figure 1) Figure 50 mm 50 mm 50 mm…

Q: The five-bolt connection shown must support an applied load of P = 480 kN. If the average shear…

Q: A hollow shaft with an outside diameter of D=54 mm and an inside diameter of d = 40 mm is subjected…

A: To determine the shear stress on the element, we can use the torsion equation: τR=TJhere,τ=The shear…

Q: A circular rod of cross-sectional area 2 x 10m² has a tensile force of 80 kN applied to it. The…

Q: A beam having the cross section shown is subjected to a vertical shear V. NOTE: This is a multi-part…

A: Consider the distance y from the bottom end where the shear stress is maximum. As shown in the…

Q: A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diameters respectively equal…

Q: Calculate the shear modulus (G) for a cylindrical steel specimen. Assuming the elastic modulus is…

Q: A steel bar is stresses to 250 MPa. The modulus of elasticity is 250 GPa. The bar is 80 mm diameter…

Q: Problem 3: The rectangular bars shows are in tension and are joined together by two bolts as shown.…

A: Given rectangular bars having joined by two bolts given the bolts have diameter d of 38inch and…

Q: Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P…

A: Consider the given data as below. Diameter of wire CD, dw=18 inch Diameter of the pin at B, dp=18…

Q: A steel rod 55 cm long has a diameter of 35.0 cm. The compressive strength (the maximum stress it…

Q: A metal slab of side (74+ 75) cm and thickness (74 + 25) cm is subjected to a tangential force of…

Q: a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial compressive…

A: Write the given values with the suitable variables. P=250 kN=250×103 Nb=0.12 md=0.05 mt=0.003 m…

Q: The steel rod with a diameter 15 mm is applied by a load of 15KN due to the load the diameter of the…

Q: Nylon strips are fused to glass plates. When moderately heated the nylon will become soft while the…

A: Given data: Observe from the diagram, Total displacement of layers D = 2 mm Height of stripe L = 5…

Q: Two solid cylindrical rods support a load of P = 37 kN as shown in Figure below. R has a diameter of…

A: We know that we first draw a free body diagram of the system given as Now We calculate the angle…

Q: For the given state of stress, determine: (1) The principle stresses and the directions of the…

A: Solution:- 1). In the figure given we have: σx= 350…

Q: Find the modulus of elasticity of a cast iron rod of diameter 20 mm and length 250 mm subjected to a…

A: Diameter of rod = 20 mm So, radius, r = 10 mm = 10-2 m Length of rod, L = 250 mm = 0.25 m Tensile…

Q: P-2. A steel shaft 2 m long that has a diameter of 90mm. is subjected to a torque of 10 KN-m. Use G…

Q: Determine the outside diameter of a tube if the stress is limited to 128 MN/m2 and a hollow steel…

Q: maximum shear = 60 MPa and modulus of rigidity = 77 GPa. Basing from the angle of twist determine…

Q: Example: A lever is keyed to a shaft 38mm diameter (Ø) the width of the key is 13mm and its length…

A: a = 0.915 m d = 38 mm = 3.8 cm = 0.038 m r = d2 = 3.82 = 1.9 cm = 0.019 m w = 13 mm = 0.013 m l = 50…

Q: P-1. A steel shaft 2 m long that has a diameter of 90mm. is subjected to a torque of 10 KN-m. Use G…

A: Given data d=90 mmT=10 kN-mG=200 GPa Here, d is the diameter and T is the torque. While G is the…

Q: A structural steel bar with a 3.6 in. x 0.890 in. rectangular cross section is subjected to a…

Q: Calculate the work done in stretching steel wire of length 2 m and of cross sectional area 0.0225…

A: To find-Work done (W)=?Given-Length (L)=2 mArea (a)=0.0225 mm2=0.0225×10-6 m2Load (F)=100 NYoung's…

Q: The rigid bar A,B,C shown in figure is connected to to a steel bar at A, Aluminum bar at B. the…

A: Using compatibility relation, ∆A7=∆B3=∆D33∆A=7∆B∆B=∆D Take moment about c,…

Q: 2. A tall building with a cross-section A, a mass M and a Young's modulus Y has a height L on Earth.…

A: The mass of the building is M Area of cross section is A Young's modulus Y Height of the building is…

Q: Mechanical engineering question. Need diagram and explanation. No chatgpt.

A: Step 1: Step 2: Step 3: Step 4:

Q: A force is applied to a circular surface with area 70 cm². The surface is parallel to the x-y plane.…

Q: te=120 (2) 457 tレ Oa = 60 the figure (0,c=0), find the principal Q-For the plane stress case shown…

A: Given : A plane stress case.

Q: I the stress experience when deformation is caused by tangential forces to the surface * O Inertia O…

A: The stress experienced when force is applied perpendicular to surface is called compressive stress .

Q: c) Table 1(c) shows the information of materials A and B. Compute the maximum stress that is applied…

A: Given: tensile stress σa = 13 MPamaterial A:σc = 240 MPa2c = 2.4*10-2 mmρt=1.2*10-4 mmmaterial B:σc…

Q: A 7-kip · ft torque is applied to a hollow aluminum shaft having the cross section shown. Neglecting…

A: Given data- T=7 kip-ft Radius of outer circle, r0=7 in Radius of inner circle, ri=14 in-4 in-2 in2=4…

Q: -10 ft 150 k-ft B - 10 ft- 60 к Į C -10 ft

A: Basic question from Shear force and Bending moment. Please have a good look

Q: 2. A tubular aluminium bar of a square cross section with outside dimensions of 50 mm x 30 mm,…

A: Given that Torque,T=300 Nm shear stress,S=20 MPa=20×106 Pa Allowable rate of twist,θ=0.025 rad/m…

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 2150 mm² and an…

Q: 2. Three steel bolts are to be used to attach the steel plate shown to a wooden beam. Knowing that…

A: Load, Ultimate Shearing Stress, Factor of Safety, F.S = 3.25

Q: Two steel plates are fastened together using four bolts. The bolts each have a shear modulus of 80.0…

Q: 2. A Torque of magnitude T = 900 N.m is applied at D as shown. Knowing that the diameter of shaft AB…

Concept explainers

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

A reinforced concrete column 400 mm in diameter is designed to carry an axial compressive load of 400 kN. Determine the required area of reinforcing steel if the allowable stresses are 6 MPa and 120 MPa for the concrete and steel, respectively. Use Econcrete = 14 GPa and Esteel = 200 GPa. %D
Please Asap
P-3. A 50 mm diameter steel shaft rotates at 240 rpm. If the shearing stress is limited to 82 MPa. The maximum torsional force developed in the steel shaft is_ KN-m 2.013 4.814 7.682 10.065 12.457
Between each pair of vertebrae in the spinal column is a cylindrical disc of cartilage. Suppose that such a particular disc of cartilage has a a radius of 3.118 cm (100cm = 1 meter) and a thickness of 6.877 mm (1000mm= 1meter). The shear modulus of cartilage is 1.2 × 107 N/m2. Suppose that a shearing force of magnitude 9 N is applied parallel to the top surface of the disc while the bottom surface remains fixed in place. How far does the top surface move relative to the bottom surface in microns (1 meter = 106 microns)?
80. Between each pair of vertebrae in the spinal column is a cylindrical disc of cartilage. Typically, this disc has a radius of about 3.0 X 10-² m and a thickness of about 7.0 x 10-3 m. The shear modulus of cartilage is 1.2 × 10' N/m². Suppose that a shearing force of magnitude 11 N is applied parallel to the top surface of the disc while the bottom surface remains fixed in place. How far does the top surface move relative to the bottom surface?
The simple truss is loaded by a system of forces as shown in the figure. The truss is supported by a pin at D and a roller at C. IfP= 800 lb, then the force developed in the member (FE) is. 500 lb 3 ft -3 ft- E DI 31- 3 ft VP Select one: Oa 1200 ib- Tension 05 1000 16 - Compression O C 2100 lb-Tension Cd 1020 lb- Compression
Two wooden members, each having a width of b = 2.4 in. and a depth of d = 0.8 in., are joined by a simple glued scarf joint. Assume B = 47°. If the allowable shear stress for the glue used in the joint is 94 psi, what is the largest axial load P that may be applied? Answer: P = i ! Ib
B8
Give the complete, detailed, step by step solution.
The wood beam is subjected to a load of 12 kN. If grains of wood in the beam at point A make an angle of 25 with the horizontal as shown, determine the normal and shear stress that act perpendicular to the grains due to the loading.
7. A wire of length 6.5 m with a cross-sectional area of 0.14 cm2 stretches by 4.5 mm when a load of 0.800 kN is hung from it. What is the Young's modulus for this wire?
A structural steel bar with a 3.6 in. x 0.890 in. rectangular cross section is subjected to a tensile axial load of 54 kips. Determine the maximum normal and shear stresses in the bar. Answer: Omax i ! ksi %3D Tmax = i ksi