A solid steel shaft supports loads PA = 500 N and PD = 580 N, as shown. Assume L1= 230 mm, L2 = 410 mm, and L3 = 350 mm. The bearing at B can be idealized as a roller support and the bearing at C can be idealized as a pin support. If the allowable bending stress is 22 MPa, determine the minimum diameterd that can be used for the shaft. D B L1 L2 L3 Pp PA Answer: d = i mm. Attempts: 0 of 1 used Submit Answer Save for Later

A solid steel shaft supports loads PA = 500 N and PD = 580 N, as shown. Assume L1= 230 mm, L2 = 410 mm, and L3 = 350 mm. The bearing at B can be idealized as a roller support and the bearing at C can be idealized as a pin support. If the allowable bending stress is 22 MPa, determine the minimum diameterd that can be used for the shaft. D B L1 L2 L3 Pp PA Answer: d = i mm. Attempts: 0 of 1 used Submit Answer Save for Later

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Read the question carefully and give me right solution with clear calculations
1. Answer Set A only
Consider the loads of the figure to be axially applied at sections B, C, and D to the concrete structure supported at A. IW E F P G 5 kN 5 kN A Determine P in kN when member BC is 24 mm in diameter, the axial stress in section F is 588 MPa, and W 309822 N. = 10 kN C 10 kN Rigid -bearing plates
From Steel Design Topic Include complete solution
Detailed Solution please
The control arm is subjected to the loading shown. The allowable shear stress for the steel pin is τ = 10 ksi. Determine the required diameters of the steel pins at A and C. Write your final answer to the nearest three decimal places.
The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a = 250mm, b = 100mm, c = 90mm, and θ = 40°. Pin B is in a double-shear connection and has a diameter of 29 mm. The bell crank has a thickness of 31 mm. Determine the shear stress in pin B and bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest hundredths.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 18 ksi, the normal stress in brass rod (2) must be limited to 23 ksi, and the normal stress in steel rod (3) must be limited to 14 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 8 kips, Q = 6 kips, R = 16 kips and S = 23 kips. SI (1) VQ (2) (3) A Answer: F₁ = B R C D First: Calculate the internal force (positive if tensile, negative if compresive) in rod (1). Use a FBD cutting through the rod in the section that includes the free end A. i kips.
4
Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 L3=1350 GPa. L2=2150 A L1 E Dia. 1 L1=1350 Р3-25 P1 L2 Dia. 2 P2=40 P2 P1=105 Dia2=45 L3 P3 D D 35 mm o Dia1=60
If P=13000 N, d=22mm and t=33mm, determine the bearing stress between the rivets and plate, in MPa?
I Review Part A The 60-mm-diameter shaft is made of 6061-T6 aluminum. (Figure 1) If the allowable shear stress is Tallow = 80 MPa, and the angle of twist of disk A relative to disk C is limited so that it does not exceed 0.035 rad, determine the maximum allowable torque T Express your answer to three significant figures and include the appropriate units. µA T = 3.7216 Units Figure Pearson