A solid cylinder of diameter D, length L, and density p, falls due to gravity inside a tube of diameter Do. The clear- ance, Do – D<< D, is filled with fluid of density p and viscosity µ. Neglect the air above and below the cylinder. Derive a formula for the terminal fall velocity of the cylin- der. Apply your formula to the case of a steel cylinder, D = 2 cm, Do = 2.04 cm, L = 15 cm, with a film of SAE 30 oil at 20°C. - %3D

A solid cylinder of diameter D, length L, and density p, falls due to gravity inside a tube of diameter Do. The clear- ance, Do – D<< D, is filled with fluid of density p and viscosity µ. Neglect the air above and below the cylinder. Derive a formula for the terminal fall velocity of the cylin- der. Apply your formula to the case of a steel cylinder, D = 2 cm, Do = 2.04 cm, L = 15 cm, with a film of SAE 30 oil at 20°C. - %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A plate 0.05mm distance from a fixed plate moves at 1.25 m/s and required a force per unit area of 3 Pa to maintain this speed by using an oil of specific gravity 0.65. Find the dynamic viscosity in centipoise and kinematic viscosity in stokes of the fluid between the plates. Calculate the specific weight in kN/m³, density, and the specific gravity of a liquid having a volume of 662900 cm and weight of 55 kN
04/13/2021 For this exercise Study and Derive the Bernoulli equation starting with the application of Newton’s second law to a fluid particle.
solve 20-30 mins i'll give you multiple upvote( handwritten asap)How can I solve the problem below in viscous fluid flow?
a band moves at a speed V and is in contact with a surface of an oil tank with viscosity m. calculate the power in watts required if the belt is moving at 2.9 m / s over SAW 30W oil at 20 C with L = 2m, b = 60m, Nu = 329.0mm ^ 2 / s, rho = 0.9g / cm ^ 2 and h=3cm
3.1 A cylindrical plug, 120mm long with a diameter of 95 mm, slides concentrically in a fixed cylinderwith an internal diameter of 95,2 mm. The radial clearance is filled with oil with a viscosity of 0.2 Pa.sCalculate the Force required to slide the plug along the cylinder at a speed of 5 m/s against the viscousresistance of the oil, the power lost due to the viscous resistance and the Kinematic viscosity of the oil ifits density is 850 kg/m 3 . A pressure intensifier is used in reverse deboost the pressure in a hydraulic system from 15MPa to7MPa. The volume of fluid required in the low pressure side is 700ml and the length of the stroke of thepiston is to be half the diameter of the low pressure piston. Calculate the diameters of the high-pressureand low pressure sides as well as the stroke length of the piston.
Dimensionless friction velocity μ*
In theoretical fluid mechanics
I need the answer as soon as possible
The block of weight W = 50 N is pulled by a weight W0 = 60 N along the surface of a table by means of an inextensible cable and a pulley. Between the block and the table there is a uniform layer of oil of viscosity m = 0.1 Pa-s and clearance h = 2 mm. The contact area is 0.01 m2. Find the terminal velocity U if the table is very long.
2. Consider the boundary-layer momentum equation for steady incompressible flow in two dimen- sions: ди dpe ду du du + po ay dx Assume the viscosity, u, to be constant. What does this equation simplifies to at a stationary solid surface? Based on this result, is a boundary layer more likely to separate in a favourable gradient (pressure decreasing) or an adverse pressure gradient? Sketch the velocity profile of a boundary layer that is attached and one that is separated. pressure
Oil Coating: A long, continuous belt is pulled upwards through a chemical oil bath at velocity V0. The belt has rectangular cross-section and has length (L), width into the paper (W). The belt picks up a film of oil of thickness h, density ρ, and dynamic viscosity μ. Gravity g tends to make the oil drain down, but the movement of the belt keeps the fluid from running off completely. Assume fully developed, steady, laminar, incompressible and two-dimensional flow of oil to answer the following questions. Assume that no pressure gradient is needed in the vertical direction to drive the film flow. Also assume that the shear stress at the air-oil interface is zero (free shear condition). Assume no-slip condition for the fluid in contact with the moving belt. Justify any other assumptions you may make. Show all steps. (a) Derive an expression for the two-dimensional velocity field inside the oil film in terms of the known parameters. Clearly indicate your co-ordinates and origin. You must…
Fluid Mechanics Expert Please