A solid cylinder 5 meters in diameter and weighing 50 KN is at rest on a 45-degree inclined plane. The coefficient of static friction is 0.25 and of kinetic friction is 0.20. Compute the centroidal mass moment of inertia of the cylinder when it is released to the inclined plane

A solid cylinder 5 meters in diameter and weighing 50 KN is at rest on a 45-degree inclined plane. The coefficient of static friction is 0.25 and of kinetic friction is 0.20. Compute the centroidal mass moment of inertia of the cylinder when it is released to the inclined plane

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.124P: The automobile, with center of gravity at G, is parked on an 18 slope with its brakes off. Determine...

See similar textbooks

Related questions

Q: 7.4-11 An element in pure shear is subjected to stresses T, = 26 MPa, as shown in the figure. Using ...

A: Given that, τxy=26 MPa, Calculate the plane angle, tanθ=34θ=tan-134θ=36.87° Drawing the Mohr's cir...

Q: 1. Steam at a temperature of 2500C has a specific volume of 0.15436 m3/kg. What are the pressure, sp...

Q: A 5.4 kg ball with a diameter of 11 cm is dropped form an airplane at an altitude of 9 km above the ...

A: Given data Mass of the ball = 5.4 kgDiameter = 11 cm = 0.11 mThe ball is dropped from an altitude of...

Q: Matrixs A, B and C are m x n, n x n and n x m, respectively. The CAB matrix is sized...

Q: 39cm 7ア What is the type of robot? DH Table? What is

A: there are 7 diffrent types of robot* Articulated* cartesian* collaborative robots* SCARA* cylindical...

Q: Determine the force in member EF and state if the member is in tension or compression. Express your ...

Q: (a) Determine the reactions at A and E if P = 600 N. The reactions are positive if to the right or u...

A: (a) Ax = -975.89 N Ay = 2137.56 N Ex = 2493.34 N. (b) Pmax = 1368.78 N.

Q: t K P (KPa) Y (%) h (KJ/kg) | U (KJ/kg) | S (KJ/kgK) Vx103 State m/kg 380 2013.2 353 70 300 859.6 61...

A: (1): At saturation pressure→P1=380 KPa: temperature→t1=141.7°C=414.85 K →hf=597.41 KJKg, hfg=2138.24...

Q: The composite beam shown in the Figure below is formed of a wood beam and a steel reinforcing plate....

Q: A small rock is thrown vertically upward with a speed of 18.0 m/s from the edge of the roof of a 30....

Q: Determine whether the unity feedback system below with G(s)

A: To determine whether the given unity feedback system is stable.

Q: a refrigerator operating on the reversed carnit cycle provides a refrigerated space at 4C while in a...

Q: 25 °C = 997 kg/m3 ero for sensible heat, g

A: we will use Priestly taylor method evaporation E =1.26∆∆+rRnet-sλ∆∆+ r= 0.676Rnet =200 w/m2

Q: At the beginning of compression an ideal Diesel cycle using air has a pressure of 15 psia, a tempera...

Q: A power plant delivering 900 MWe has an efficiency of 30% with 15 percent of the waste heat being re...

Q: oment diagrams for the beam shown below. 60KN A 30KN.m B. 2m 1m

Q: 12-lb weight stretches a spring 2 ft. The weight is released from a point that is 1 ft below the eq...

Q: Determine the resuhant moment produced by the forces about point O. F, = S00N 125 m, 025 m

A: Given:F1=500 NF2=600 N

Q: A rankine cycle operates between a pressure limit of 6 MPa. and 50 kPa., the steam leaves the boiler...

Q: Consider shaft AB fixed at point A and free at point B that is subjected to the torque T. The shaft ...

A: Member subjected to torque can be two types of analysis 1. Series 2. Parallel.

Q: bullet's speed?

A: To find Bullet speed

Q: The composite beam shown in the Figure below is formed of a wood beam and a steel reinforcing plate....

Q: M1 U5: Use the general solution in determining the total hydrostatic force acting on the submerged c...

Q: A turbine develops 144 HP running at 100 rpm under a head of 7.7 meters. What horsepower would be de...

Q: A piston-cylinder with 25 grams of saturated water within. Is kept at a pressure of 300 kpa. A heate...

Q: Engr. Dizon, a mechanical engineer, is planning to construct a cooling water pond in Laguna for a po...

Q: A thin plate with uniform thickness of 2 mm, on which there are two circular holes and a hole compos...

Q: Q5. A material is made in circular rod form of diameter 1.5 cm and 200mm long. It is fixed on the Un...

Q: The thermal conductivity of a sheet of rigid, extruded insulation is reported to be k = 0.029 W/m·K....

A: Answer: (a) The heat flux through a 3m × 3m sheet of the insulation is 11.6 W/m2. (b) The rate of he...

Q: B. A machine - part needs 14 bolts a How many bo43 are needed For 25 nachine -parts? b. wnat is the ...

Q: Find the Experimental specific heat of metal, cm

Q: A SCARA manipulator which has two revolute joints (0,A) and one prismatic joint (B) is shown in Figu...

Q: For the beam shown and the cross section, :the value of bending moment is equal to

Q: An isosceles triangular plate of base 3 m and altitude 3 m is immersed vertically in an oil of speci...

Q: After one particularly wild night at the bars, Jon decides to come home and jump on his bed (see Fig...

A: The bowing moment at a given part of a shaft is characterized as the resultant second about that seg...

Q: 5 m. How long does the toy plane take to

A: Need to find Time required for the toy plane to travel once around circle

Q: A vertical square prism of 40 mm base side is completely penetrated by horizontal square prism of ba...

A: Given: Vertical Square Prism: Height = 100 mm (assumed) side = 40 mm face Angle of prism with VP ...

Q: he workpiece by a pneumatic cylinder. The rom any one of three work stations. The pund ered when 2 s...

A: designing of equivalent pneumatic and electrical circuit

Q: 1011. A balloon rises from the ground with a constant acceleration of 4 ft per sec. Five seconds lat...

Q: of the links AB and CD is made of aluminum (E=75 GPa) and has a cross - sectional area of 125 mm?. K...

Q: The revolving crank ED and connecting link CD cause the rigid frame ABO to oscillate about O. For th...

A: ω=0.4rad/sα=0.06rad/sAF=2mFB=3mFC=2mCO=1.5mCD=1.5mDE=0.5m To-Find Acceleration of point A wrt B

Q: Determine the moment about point A due to the three applied forces on the frame to the right. Answer...

Q: What is the capacity of an engine in cc with four cylinder that has bore x stroke = 79 mm x 77 mm? S...

A: Given:Bore diameter, d=79 mmstroke length, l=77 mmnumber of cylinder, n=4

Q: A gas turbine compressor unit receives 32.6m^3/min of air at 98kPa and 295K and compresses it in a r...

Q: Construct the shear and moment equations of the loaded beam as shown and draw the shear and moment d...

A: Let RO and RC are the reactions at point O and C respectively. Let's mark the points D and E as sh...

Q: general, when a two degree of freedom system without external forcing, is subjected to a general ini...

A: When a two degree of freedom system without external forcing is subjected to a general initial condi...

Q: Determine the resultant moment about the point (A) for all forces as shown in figure below: * Fj = 3...

Q: As shown in Figure 5, disk A is free to spin about the bar B, which is perpendicular to the disk and...

A: the disk spins without slipping ω=ωs+ωo is always directed along the instantaneous axis of zero v...

Q: The percentage of reduction in area of The final area would be: magnesium tensile specimen was 25%, ...

A: Given∆A%=-25L=56mdi=20mm

Q: Boom AD is supported by a ball & socket at D, and two ropes (AB and AC). B, C and D lie in the yz pl...

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The cable spool shown at the right has a weight of 50 lbs and has a moment of inertia of .28 slug-ft^2. Assume the spool rolls without slipping when we apply a 50-lb tension in the cable. Find: friction force between the spool and the ground.
An object of mass 40 kg has a radius of 0.2 m. If the surface is tilted, there is enough friction that Prevents slipping. Calculate the force of friction acting on this object during its downward roll and the time it takes to roll on a 2 m long incline. 1. The object is a thin wall cylinder. 2. The object is a solid cylinder. 3. The object is spherical
Solve it correctly please. I will rate accordingly with 4votes. A 275-N solid sphere rests on a 35-degree inclined plane from thehorizontal. If the sphere has a diameter of 30 cm, calculate themagnitude of a horizontal force P passing through the center of thesphere and the reaction force of the inclined plane in order tomaintain the sphere at rest.
Consider the system of two blocks. Thereis no friction between block A and the tabletop. The mass of block B is5.00 kg. The pulley rotates about a frictionless axle, and the light ropedoesn’t slip on the pulley surface. The pulley has radius 0.200 m andmoment of inertia 1.30 kg . m2. If the pulley is rotating with an angularspeed of 8.00 rad/s after the block has descended 1.20 m, what is themass of block A?
A sphere of mass M and radius R is not necessarily solid or hollow. It has moment of inertia I= cMR2. As shown in the figure, the sphere starts from rest and rolls without slipping down a ramp from height H. It then moves back up the other side, but now with no friction at all between the sphere and the ramp. What height does the sphere reach?
6. In a Porter governor, the upper and lower arms are each 250 mm long and are pivoted on the axis of rotation. The mass of each rotating ball is 3 kg and the mass of the sleeve is 20 kg. The sleeve is in its lowest position when the arms are inclined at 30° to the governor axis. The lift of the sleeve is 36 mm. Find the force of friction at the sleeve, if the speed at the moment it rises from the lowest position is equal to the speed at the moment it falls from the highest position. Also, find the range of speed of the governor.
6. In a Porter governor, the upper and lower arms are each 250 mm long and are pivoted on the axis of rotation. The mass of each rotating ball is 3 kg and the mass of the sleeve is 20 kg. The sleeve is in its lowest position when the arms are inclined at 30° to the governor axis. The lift of the sleeve is 36 mm. Find the force of friction at the sleeve, if the speed at the moment it rises from the lowest position is equal to the speed at the moment it falls from the highest position. Also, find the range of speed of the governor. [Ans. 9.8 N; 16 r.p.m.]
A skier starts from rest on the 39° slope at time t = 0 and is clocked at t = 2.60 s as he passes a speed checkpoint 20 m down the slope. Determine the coefficient of kinetic friction between the snow and the skis. Neglect wind resistance. 39⁰
Derive the equations of motion of the block of mass m1 in terms of its displacement x. Surface frictions and pulley inertia are negligible, the cylinder has a mass of m2 and doesn’t slip.
A truck weighing 35 tons is travelling at 32 km/h round a curve track of 43 m radius. If the center of gravity of the truck is 2.3 m above the rails, calculate the vertical reaction of each wheel if the wheel distance is 1.7 m apart. Additionally, if the track is banked at 130 and the coefficient of friction is 0.4, find the truck maximum speed.
A solid homogeneous cylinder of radius r = 0.5m and mass of m = 100kg is rolled up a 0 20° incline by a force of P = 350N starting from rest. Compute the velocity vG of the center of mass of the cylinder into 6 seconds of motion. Note: Mass moment of inertia about G is given as IG = (1/2)mr². W,a v,a G m Your answer: 32.2 m/s 80.6 m/s 364.5 m/s 9.5 m/s 444.5 m/s 73.0 m/s
A vehicle of total weight 49050 N is held at rest on a slope of 10°. It has a wheel base of 2.25 m and its centre of gravity is 1.0 m in front of rear axle and 1.5 m above the ground level. Find What are the normal reactions at wheels assuming that sliding does not occur first, what will be the angle of sloe so that the vehicle will overturn? Assuming all the wheels are to be braked what will be the angle of slope so that the vehicle will begin to slide if the co-efficient of adhesion between the tyre and the ground is 0.35?