A solid cube of side 2a and mass Mis sliding on a frictionless surface with uniform velocity v as shown in Figure Pl1.50a. It hits a small obstacle at the end of the table that causes the cube to tilt as shown in Figure Pl1.5Ob. Find the minimum value of the magnitude of v such that the cube tips over and falls off the table. Note: The cube undergoes an inelastic col- lision at the edge. - 2a - M a b. Figure P11.50

A solid cube of side 2a and mass Mis sliding on a frictionless surface with uniform velocity v as shown in Figure Pl1.50a. It hits a small obstacle at the end of the table that causes the cube to tilt as shown in Figure Pl1.5Ob. Find the minimum value of the magnitude of v such that the cube tips over and falls off the table. Note: The cube undergoes an inelastic col- lision at the edge. - 2a - M a b. Figure P11.50

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

ASSIGNMENT No. 12: Moments of Inertia Solve for the moment of inertia of areas and solids of revolution. Solve and draw the following: Find the moment of inertia with respect to the axis of revolution of a circular cone.
help asap
B1
Current Attempt in Progress The figure shows particles 1 and 2, each of mass m, attached to the ends of a rigid massless rod of length L₁ + L2, with L₁ = 2.0 m and L₂ = 3.0 m. The rod is held horizontally on the fulcrum and then released. What are the magnitudes of the initial accelerations of (a) particle 1 and (b) particle 2? (a) Number (b) Number Units Units 1 L > >
A uniform hollow spherical ball of mass 2.14 kg and radius 0.56 m rolls without slipping up a ramp that rises at 30.0° above the horizontal. The speed of the ball at the base of the ramp is 3.42 m.s1. While the ball is moving up the ramp, find (a) the magnitude of the acceleration of its center of mass. m.s2 (b) the magnitude of the friction force acting on it due to the surface of the ramp. N
It is sometimes important to determine the location of a person’s center of gravity(which coincides with the center of mass because the gravitational force is uniform at the scale of the human body). This can be done with the arrangement shown intheFigure below. A light (negligible mass) plank rests on two scales that read Fg1=380 N and Fg2=320 N. The scales are separated by a distance of 2.00 m. How far from the woman’s feet is her center of gravity?
A uniform, thin, spherical shell of radius, R, and mass, m, is rolling without slipping or sliding on a level surface. If the center-of-mass velocity of the ball is vCM what is the total kinetic energy of the ball? Hint: 2/3 mR2
I need it asap
A uniform solid sphere of mass 6.0 kg and radius 10 cm is rolling without slipping along a horizontal surface with a speed of 4.9 m/s (this is the speed of the center of mass) when it starts up a ramp that makes an angle of 30° with the horizontal. 1st а) b) While the ball is moving up the ramp, find What is the maximum distance it can go up the ramp, measured along the surface of the ramp? 2nd? the acceleration (magnitude and direction) of its center of mass and i) ii) | 3rd 3] the friction force (magnitude and direction) acting on it due to the surface of the ramp. Moment of inertia of a solid sphere is I em =MR². ст
. A part of a mechanical linkage has a mass of 3.6 kg. Its moment of inertia Ip about an axis 0.15 m from its center of mass is Ip = 0.132 kgm². What is the moment of inertia Icm about a parallel axis through the center of mass? (0.051 kgm²) cm Axis through center of mass Axis through P