A solid circular steel shaft having an outside diameter of 1.50 in. is subjected to a pure torque of T = 8330 lb-in. The shear modulus of the steel is G = 12,000 ksi. Determine the maximum shear stress in the shaft. a. 7.64 ksi b. 12.57 ksi c. 13.20 ksi d. 10.33 ksi e. 15.86 ksi

A solid circular steel shaft having an outside diameter of 1.50 in. is subjected to a pure torque of T = 8330 lb-in. The shear modulus of the steel is G = 12,000 ksi. Determine the maximum shear stress in the shaft. a. 7.64 ksi b. 12.57 ksi c. 13.20 ksi d. 10.33 ksi e. 15.86 ksi

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Compound shaft ACB is fixed at A and consisting of two solid circular sections AC & CB, as shown,…

Q: If the allowable shear strength of aluminum is 45 MPa, determine the minimum thickness, t, of the…

Q: must transmit the torque of 34 kN-m. The total angle of twist must not exceed 3°. The maximum…

Q: Under normal operating conditions, the electric motor exerts a torque of 2.4 kN·m on shaft AB. Each…

Q: A circular solid shaft made of vibranium has G=80 MPa and has a limiting torsional shear stress of…

Q: Determine a.) the maximum torsional stress, τmax, and b.) the maximum angle of twist, φ, of the…

Q: The solid rod AB has a diameter dAB5 60 mm and is made of a steel for which the allowable shearing…

A: Given Data: The diameter of the rod AB is: dAB= 60 mm The outer diameter of the pipe CD is: dCD=90…

Q: Shafts A and B are made of the same material and have the same cross-sectional area, but A has a…

Q: 4

A: Please see the attached image for the answer.Explanation:

Q: The solid shaft (loaded as shown) is made of material that has an allowable shear stress of 10 MPa.…

A: The solid shaft (loaded as shown) is made of material that has an allowable shear stress of 10 MPa =…

Q: Knowing that the lengths of the shown solid shafts are AB-60mm and BC=80mm, determine the torque TA…

A: Given. TB = 400 Nm θAC=3o G = 77 MPa LAB = 60 mm LBC = 80 mm

Q: The electric motor below, exerts a torque of 800 N.m on the steel shaft ABCD when it rotates at…

Q: The driveshaft of an automobile is being designed to transmit 197 hp at 3810 rpm. Determine the…

A: GivenP=197hpN=3810rpmσ=5600psi

Q: The driveshaft of an automobile is being designed to transmit 203 hp at 2940 rpm. Determine the…

Q: 2. A steel marine propeller shaft 24 in. in diameter and 16 ft long is subjected to a torque of 2400…

Q: Q5: Determine the diameter of the solid shaft where the angle of twist not exceed 10 and the length…

A: Given: The angle of the twist: →θ=1°=1×π180=0.017 radian Diameter of the shaft=d And length of the…

Q: Determie the rotation or twist in degrees of a shaft, 742 mm long subjected to a torque of 95 N-m,…

A: According to the given datawe need to findThe angle of the twist

Q: 1. A solid aluminum shaft 4 m long that has a diameter of 120 mm is subjected to a torque of…

Q: 324. A shaft composed of segments AC, CD, and DB is fastened to rigid supports and loaded as shown…

Q: Determine the maximum torsion load, in N-m, that a 16 mm diameter aluminum shaft can carry if its…

Q: The compounded A-36 steel shaft (GA-36 steel = 75 GPa) is fixed to the wall at A and is subjected to…

A: given data:A 36-steel shaft Modulus of rigidity = 75 GPalength of AEB = 2m length of BDC = 1m torque…

Q: A single torque of T = 60 N.m is applied to a compound torsion member. Segment (1) is a 32-mm…

A: The angle of rotation: The angle at which the fixed end rotates with respect to the free end is…

Q: posite shaft shown, composed of a steel (G = 77 GPa) core inside an aluminum (G = 25 GPa) jacket,…

Q: A circular shaft AB consists of a 10-in.-long, 78-in.-diameter steel cylinder, in which a…

A: Given data: The applied torque, T = 90 lbˑ The diameter of rod at A is, dA = 78 in. The diameter of…

Q: 3. The stepped shaft shown is supported by bearings at A and B. Determine the maximum stress in the…

A: Given Data r=3 mm

Q: determine the bolt diameter required in mm. (b) If the shaft is made of the same material as the…

Q: 7. What is the maximum torque in kN-m that can be applied to a hollow circular steel shaft of 120 mm…

Q: 3. A machine shaft is supported on bearings 1 m apart is to transmit 190 KW at 300 rpm while…

Question

a. 7.64 ksi

b. 12.57 ksi

c. 13.20 ksi

d. 10.33 ksi

e. 15.86 ksi

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

A solid steel shaft will not twist through more than 3 degrees in a 6-m length when subjected to a torque of 12 KN*m. The modulus of rigidity of the steel shaft is 83 GPa. Determine; a) Diarneter of the shaft. (. b) Maximum shearing stress developed in the shaft.
The design specifications for the steel shaft AB require that the shaft acquire a strainenergy of 34 N.m as the 2.8 kN.m torque is applied. Using G = 72 GPa, determine(i) the largest inside diameter of the shaft that can be used,(ii) the corresponding maximum shearing stress in the shaft.
3. A solid circular shaft is 1.8 m and is made of steel with G = 70 GPa. When rotating at w = 70 rad/s, it transmits 28 kW of power from engine A to generator B. As the design engineer, you are asked to: (a) Determine the shaft's smallest allowable radius if the allowable shear stress is T allow = 80 MPa. (b) Determine the shaft's smallest allowable radius If the allowable angle of twist is allow = 0.1 rad (in other words, the shaft is restricted not to twist more than 0.1 rad). (c) If both conditions (a) and (b) are required simultaneously, which radius will you select as the allowable radius. (In other words which condition controls the situation)? Briefly explain your answer. (1 kW = 1000 Watts) B
Required information The design of a machine element calls for a 40-mm-outer-diameter shaft to transmit 43 kW. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 40 mm (a) (b) If the speed of rotation is 720 rpm, determine the maximum shearing stress in shaft a. The maximum shearing stress in shaft a is MPa.
A solid 2.9-in.-diameter bronze [ G = 7100 ksi] shaft is 8-ft long. The allowable shear stress in the shaft is 10.2 ksi and the angle of twist must not exceed 0.034 rad. Determine the maximum horsepower P that this shaft can deliver: (a) when rotating at 182 rpm. (b) when rotating at 644 rpm.
Q.12A solid shaft of diameter 'd' and length " issubjected to torque T. Another shaft B ofsome length, material but twice the diameter is subjected to the torque 2T. The ratio of the angle of twist of shaft A to shaft B is-
The 60-mm-diameter shaft is made of 6061-T6 aluminum. (Figure 1) Figure 1.20 m 1.20 m 1 of 1 Part A If the allowable shear stress is Tallow = 80 MPa, and the angle of twist of disk A relative to disk C is limited so that it does not exceed 0.060 rad, determine the maximum allowable torque T Express your answer to three significant figures and include the appropriate units. T = Submit Value Provide Feedback Request Answer Units ?
The allowable shearing stress is 15 ksi in the 1.5-in.-diameter steel rod ABand 8 ksi in the 1.8-in.-diameter rod BC. Neglecting the effect of stress concentrations, determine the largest torque that can be applied at A
The composite shaft shown consists of a 0.2-in.-thick brass jacket (Gbrass= 5.6 × 106 psi) bonded to a 1.2-in.-diameter steel core (Gsteel=11.2 × 106 psi). Knowing that the shaft is being subjected to the torques shown, determine the largest angle through which it can be twisted if the following allowable stresses are not to be exceeded: τsteel=15 ksi and τbrass= 8 ksi.
Under normal operating conditions, the electric motor exerts a torque of 2.4 kN·m on shaft AB. Each shaft is solid with diameter d 52 mm. In order to reduce the total mass of the assembly, a new design is being considered in which the diameter of shaft BC will be smaller. Determine the smallest diameter of shaft BC for which the maximum value of the shearing stress in the assembly will not be increased. The smallest diameter of shaft BC is mm.