A solid circular rod, 750 mm long and 30 mm diameter, is subjected to an axial force of 80 kN. The compression of the rod is 1.35mm, and its diameter becomes 30.015 mm. Determine the Poisson's ratio v of the material. Assume the material does not yield.(A) 20,406B) 26,404с 24,604D) 20,604 All of the following are correct exceptA Creating the bending moment diagram by parts can be done with respect to only one point/location.BIn area moment method, the deviation at any point is positive if the point lies above the tangent.ⒸThe change in slope between the tangents drawn to the elastic curve at any two points A and B is equal to the productof 1/El multiplied by the area of the moment diagram between these two points.D The moment of a load about a specified axis is always defined by the equation of a spandrel y=kx^n.

Answered: Image /qna-images/answer/4f766ff8-7ac8-4031-a9ac-e5848cc150e7.jpg

A solid circular rod, 750 mm long and 30 mm diameter, is subjected to an axial force of 80 kN. The compression of the rod is 1.35 mm, and its diameter becomes 30.015 mm. Determine the Poisson's ratio v of the material. Assume the material does not yield.

A solid circular rod, 750 mm long and 30 mm diameter, is subjected to an axial force of 80 kN. The compression of the rod is 1.35 mm, and its diameter becomes 30.015 mm. Determine the Poisson's ratio v of the material. Assume the material does not yield.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question.7 Water under pressure 8 MPa is suddenly admitted on to a plunger of 80 mm diameter, attached to a rod 25 mm diameter 2.5 m long. Find the maximum instantaneous stress and deformation of the rod. Take E= 210 GPa.
A 100mm* 40 mm* 20 mm steel block is subjected to a hydrostatic pressure of 10MPa. The Young's modulus and Poisson's ratio of the material are 150 GPa and 0.1 respectively. Determine change in volume of the block.
A railroad tie (or sleeper) is subjected to two rail loads, each of magnitude P = 178 kN, acting as shown in the figure. a- L a- The reaction q of the ballast is assumed to be uniformly distributed over the length of the tie, which has cross-sectional dimensions b = 300 mm and h = 250 mm. Calculate the maximum bending stress omay (in MPa) in the tie due to the loads P, assuming the distance L = 1,500 mm and the overhang length a = 520 mm. (Enter the magnitude.) MPa
1.2 A hollow steel rod has a length of 1m. The outside diameter of the rod is 0.2m and the inner diameter is 0.18m. The rod is compressed axially with a load of 200kN. The modulus of elasticity and the Poisson's ratio of the rod are 200GPa and 0.3 respectively. Determine the increase in outside diameter of rod using the calculated value of decrease in length. (The decrease in length=0.17mm)
A cylindrical bar of 600mm length is subjected to a tensile load of 80 kN along the axis. G = 80 GPa. The change in volume of the cylinder is 72 mm³. The poisson's ratio of the cylinder material is
A cube of material (E = 15,000 psi, v = 0.25) of side length 2" is shown in the x, y plane. Takex positive to the right and y positive up. Determine the change in length of the cube in the three coordinate directions if 4 %3D a) The normal stress in the z direction is zero (Ans: 0.0317" in x direction) b) The normal stress in the z direction is 300 psi compression (Ans: 0.0416" in x direction) 150 psi 100 psi + 200 psi
A solid circular rod is subjected to an axial load of P = 310 kN. The diameter of the rod is d = 45 mm, and its length is L = 810 mm. After load Pis applied, the elongation of the rod is ö = 4.3 mm, and its diameter becomes d' = 44.971 mm. Determine (a) the modulus of elasticity for the material. (b) Poisson's ratio for the material. P. Answer: GPa (a) E = i (b) v = i
A 100mm* 40 mm* 20 mm steel block is subjected to a hydrostatic pressure of 10MPa. The Young's modulus and Poisson's ratio of the material are 150 GPa and 0.1 respectively. Determine change in volume of the block.
Last three digit of id: 229
Q1) (A) Two solid circular cross-section bar as shown in the Figure. If the stress in left portion is limited to 150 MN/m2, determine the diameter of the left portion(D). Find also the length of the right portion(a) if the total elongation of the bar is to be 0.2mm. Young's modulus is E = 210 GN/m². (B)If, in order to reduce weight whilst keeping the external diameter constant, the left portion is bored axially to produce a cylinder of uniform thickness, whatis the maximum diameter of bore possible given that the maximum allowable stress of the left portion is 180 MN/m2? The load can be assumed to remain constant at 160 kN. 0.03 m 160 kN D 160 kN diameter a 0.4 m
Student A B D H Number 201780130 2 1 7 8 1 3 Evaluate the following variables and use them as given in the following problems. 200 if I is even, 250 if I is odd (D + G)*10 (H + I/2, if in case the result is zero, use 3 (A +C + E)*2 (P + M)*20 H + 5 M Q %3D 50(E + G + 1) II II || || || |||| ZNPORX
Please show the step-by-step solution. Please use pen and paper to solve. Thank you. Direction: Determine the degree of indeterminacy and stability of the following structures. Classify each as stable or unstable. 囲 8.