A solid aluminum shaft shown below has an allowable shear stress of 92 MPa, and the angle of twist of disk A relative to disk C is to be limited to a maximum of 0.05 radian. The diameter of the shaft is 80 mm and shear modulus is 28 GPa. Determine the maximum allowable torque T. 1.20 m B 1.20 m 23

A solid aluminum shaft shown below has an allowable shear stress of 92 MPa, and the angle of twist of disk A relative to disk C is to be limited to a maximum of 0.05 radian. The diameter of the shaft is 80 mm and shear modulus is 28 GPa. Determine the maximum allowable torque T. 1.20 m B 1.20 m 23

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A steppe

Q: A torque T = 9.5 Kn - m was applied. Determine and the angle of twist in degrees if the shaft has l…

Q: Q4- A circular shaft consists of steel and aluminum segments is subjected to the torques shown in…

Q: For the overhanging beam loaded as shown, determine the maximum values of flexural stress and…

A: Given A beam Required Maximum flexural and shear stress

Q: A circular shaft is subjected to a twisting moment Tand bending moment M. The ratio of maximum…

A: Given data- Circular Shaft- Twisting Moment = T Bending Moment = M

Q: The solid aluminum shaft has a diameter of 50 mm and an allowable shear stress of Tallow - 6 MPa.…

A: Given data, Radius of shaft (r) = 25 mm Allowable shear stress = 6 MPa

Q: what is the maximum torque (To)max that may be applied at section C?

Q: ular bar is to withstand a bending moment of 10 kNm and a torque of 30 kNm. the diameter of the bar…

Q: Ipf T One segment has a diameter of d, = 56 mm and length of L, = 1.65 m; the other segment has a…

Q: Q- The minimum shear stress in a hollow shaft of outer diameter 40 mm and thickness 5 mm subjected…

A: outer diameter 40 mm thickness 5 mm torque = 10 Nm.

Q: What is the max shear stress on a shaft under a torque of T = 54.167 lb-ft having a diameter of 0.75…

Q: The solid shaft is subjected to the distributed and concentrated torsional loadings shown. Determine…

Q: The fixture shown in Figure 5 is fixed at point A and free at point C. The frame is made from a…

A: Given data b = 50 mm h = 75 mm E = 200 GPA Ignore axial and shear deformation Find vertical…

Q: Q3: The solid shaft is made of material that has an allowable shear stress of t lowable 60 MPa.…

A: given above figure with allowable shear stress = 60Mpa

Q: A solid 1.500-in.-diameter steel shaft is subjected to torques TB = 255 lb-ft and TD= 95 lb-ft,…

Q: The compound shaft, compose of steel, aluminum, and bronze segments, carries the two torques shown…

Q: View Policies Current Attempt in Progress A solid circular steel shaft having an outside diameter of…

Q: Problem-3 b A hollow shaft of 20 mm diameter and 16 mm inside diameter is subjected to a torque of…

A: Given- Outside diameter D=20 mm, Inside diameter d=16 mm, Torque T=40 N-m, It is needed to find the…

Q: For the overhanging beam loaded as shown, determine the maximum values of flexural stress and…

Q: 8.20 A solid shaft has diameter 80 mm. It is subjected to a torque of 4 kN-m. The maximum shear…

A: Given data: Shaft diameter, d = 80 mm Torque, T = 4 kN-m

Q: A solid shaft of 150 mm radius is used to transmit torque. Find the maximum torque transmitted by…

Q: A solid 1.250-in-diameter steel shaft is subjected to torques Tg - 190 lb-ft and Tp- 115 Ib-ft,…

A: Given data: Maximum shear stress = 12 ksi diameter of solid shaft = 1.25 in TB = 190 lb.ft TD = 115…

Q: A soid, crcular ber ABC consists of two segments, as shown in the figure One segment has a diameter…

Q: A solid bar of circular cross section has a diameter of 40mm and lenglh of 1300mm. G-80GPA and…

A: Using torsion equationTJ=τRT=TorqueJ=polar moment of inertiaR=radiusτ=shear stress

Q: The maximum torque that can be safely applied to a shaft of 100 mm diameter if the permissible angle…

A: Given data- Diameter of the shaft d=100 mm, Permissible angle of twist θ= 1 degree, Length L=3 m,…

Q: An aluminum shaft with a constant diameter of 68mm is loaded by torques applied to gears attached to…

Q: Q-1 A circular bar is to withstand a bendi Determine the diameter of the bar if the factor of safety…

Q: Problem No.3 A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter.…

A: solution Given shaft diameter d=104mm allowable shear stress ζ=48Mpaallowable angle of twist θ=2°…

Q: Q1: For the loaded simply supported beam shown in figure, if the allowable bending stress is 100 MPa…

Q: From the given system as shown. Solve for the axial deformation in the middle 50 AN 100 N 100 AN…

Q: Problem #1. The 20-mm diameter shaft is subjected to torques as shown. The shaft is made of steel…

Q: Q-1 A circular bar is to withstand a bending moment of 10 kNm and a torque of 30 kNm. Determine the…

Q: 350mmi The simply supported beam has an l-shaped cross section. (1) Determine the values and…

A: Bending stress is linearly proportional to depth. Compressive and tensile stress have same value but…

Q: 2. For the system shown below, compute the maximum torque it can accommodate if a is 2000mm and b is…

Q: Determine if the combination of both bending moment, M, of 25 kNm and a torque, T, of 34 kNm acting…

A: Pumps with short shafts, less than 30 to 50 feet long, are driven by solid shaft drivers. As a…

Q: A high-strength steel [E = 237 GPa] tube having an outside diameter of 73 mm and a wall thickness of…

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

3. A solid aluminum shaft shown below has an allowable shear stress of 92 MPa, and the
angle of twist of disk A relative to disk C is to be limited to a maximum of 0.05 radian.
The diameter of the shaft is 80 mm and shear modulus is 28 GPa. Determine the
maximum allowable torque T.
1.20 m
B
1.20 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Solution

VIEW

Step 2 torque T

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

i need the answer quickly
Q-1 A circular bar is to withstand a bending moment of 10 kNm and a torque of 30 kNm. Determine the diameter of the bar if the yield stress of the material is 250 MPa and the factor of safety is 3. Use maximum normal strain theory of failure. Take Poisson's ratio as 0.3.
3. Solve the following problem The following shaft is subjected to three torsional moments expressed as a fraction of T. Determine the maximum value of the T if the allowable shear stress is Tallow 80 MPa. Draw the torsion (torque) diagram along the shaft for that value of T, and determine the relative angle of twist between sections A and C (use a shear modulus G = 26GPa). = diameter d 60mm Tallow 80MPa G = 26 GP₂ Req'd: allowable torque T angle of twist of A relative to C PAIC Torsion diagram 1.2m 1.2m
The same torque is applied to two tubes with identical metal sheets, determine the ratio of Tcircle/ Tsquare of the shear stresses. Given: r = 12 mm, S = 22 mm, and t = 2.09 mm.
1. A steel circular bar (the yield stress oy = 350 MPa) with diameter d = 60mm is acted upon by combined moments M and axial compressive loads P at its ends. Taking P = 500 kN, determine, based on the Von Mises criterion of yield failure, the largest allowable value of M. d M M P- P.
Tb = 80.51
P7-L In cach case,calculate the value of Q and i that are used in the shear formula for finding the shear stress at A. Alsa, show how the shcar stress acts on a differential volume element located at point A. fa2m 02m tazm al aim (d) al m 03m 03 m taim Fozm le) a5m falm 402m 0.3m talm 01m (c)
The torsional element shown consists of two solid shafts; steel shaft (1) with a length of L1 = 650 mm, a diameter of d1 = 39 mm, and a modulus of rigidity of G1= 40 GPa; and copper shaft (2) with a length of L2 = 1445 mm, a diameter of d2 = 23 mm and a modulus of rigidity of G2= 85 GPa. A torque of TB = 835 N.m and a torque of TC = 300 N.m are applied on the shaft at joints B and C, respectively. [L1 = 650 mm, d1 = 39 mm, G1= 40 GPa; L2 = 1445 mm, d2 = 23 mm, G2= 85 GPa, TB = 835 N.m, TC = 300 N.m] Determine the internal torque in shaft (2).N.m Determine the maximum shear stress in shaft (2). Determine the angle of twist in shaft (1). Determine the angle of twist in shaft (2).in rad Determine the angle of twist at C with respect to the support.in rad
A 2 m long shaft is transmitting 90 kW at 150 RPM. The allowable shear stress in the material is 60 MPa. If the shaft is not allowed to twist more than 1°, then the diameter of the shaft required will be (Take G = 85 GPa)