A solenoid with a length of 45 cm is made by wrapping 450 wires around an iron rod has a cross-sectional area of 0.85 cm2 .The relative permeability of iron is 350. What is the inductance solenoid self and average emf if the current is reduced from 2 A to 0.75 A in 1/153 !

Q: In the circuit of the figure below, the battery emf is 55 V, the resistance R is 150 2, and the…

A:

Q: The time variation of the current in a 3H inductor is given by I=5+7t-7t^2, with I in amperes and t…

A:

Q: The phase angle in a certain RL circuit is 68° at a frequencyof 60.0 Hz. If R = 2.1 Ω for this…

A: Using the equation for phase angle in RL circuit, θ=tan-1XLRtanθ=XLRXL=R tanθ

Q: What percentage of the final current I0 flows through an inductor L in series with a resistor R ,…

A:

Q: An ideal air-core solenoid has a length of 6.5 cm, area of 2 cm² and 3000 turns. Find the self-…

A: Given data as per question L  = 6.5cm A =  2cm2 N =3000

Q: A Coiled telephone cord forms a spiral with 51-0 tumsa diameter of 1.30cm, and an unstretched length…

A: Given that For a spiral telephone cord the number of turns is N=51 diameter of the cord is d=1.3cm…

Q: A simple RL circuit includes a 0.125-H inductor. If the circuit isto have a characteristic time of…

A: The expression for the characteristic time of RL circuit is τ=LR Here, R is the resistance of the…

Q: The inductance of L-4 henry and resistance of 100 ohm are connected in series with the battery of…

A:

Q: URGENT An L-R-C series circuit has inductance 42.0 mH, capacitance C, and resistance R. Without the…

A: Resistance The Greek letter omega () represents the measurement unit for resistance, known as ohms.…

Q: (a) If an inductor carrying a 1.85 A current stores an energy of 0.250 mJ, what is its inductance?…

A:

Q: A battery, resistor and inductor are connected in a single conducting loop. The circuit has time…

A: Emf, V = 6.15 VTime constant, τ = 755 μs = 0.000755 sMaximum current, imax = 440 mA = 0.44 A

Q: What resistance R (in 2) must be connected in series with a 150 mH inductor and a 3.0 μF capacitor…

A:

Q: The self-inductance of the circuit in the figure below is 9.20 x 108 H. Find the back emf when the…

A: Given data, theself-inductance is given as L = 9.20 x 10-8 H.The rate of increase in current is .

Q: A solenoid of radius 4.50 cm has 600 turns and a length of 25.0 cm. - (a) Find its inductance. mH…

A: Given the radius  of the solenoid is r=4.50cm=0.045m number of turns N=600 turns  length…

Q: A 4-79 permalloy solenoid coil needs to produce a minimum inductance of 1.5 Wb/m2 . If the maximum…

A:

Q: In the circuit of the figure below, the battery emf & is 75 V, the resistance R is 150 , and the…

A:

Q: has a self-inductance of 28 H. (a)    What induced emf opposes shutting it off when 90 A of current…

A:

Voltage Across Inductor

An actor is a passive electrical component that consists of a coil bent in the form of wire which uses electromagnetism to produce electric current through the coil. When the electric current flows through a conductor that is the coil, a magnetic flux is developed around the conductor. This flow of current through the coil creates a magnetic field based on Fleming's Right-hand thumb rule. If there is any decrease in the current passing through the inductor, then the magnetic field will also decrease and energy is released through the generation of electric current. There is also a secondary voltage inducing in the same coil due to the magnetic flux, since it opposes any changes in the electric current flowing through the circuit. An inductor is also called choke, coil, or solenoid. A choke is designed to block certain frequencies when the DC current passes. A winding coil is coated with insulation to give extra insulation and protect the circuit. They are usually tightly wrapped around a central core which is cylindrical in nature so that the magnetic flux can be induced. The solenoid is a three-dimension coil that is used to exhibit electromagnetism when the magnetic field is developed due to the current flowing through the coil. The sign convention of the inductor is the same as the power dissipating device. When the current flows into the positive side of the voltage across the inductor, the value is positive and the inductor dissipates power whereas when the inductor releases the power back to the circuit, the current has a negative sign convention.