A solar water heater mounted on the roof consists of two flat plates. Water enters at A and exits at B. Assume the average temperature of the water is 45° C. (Figure 1) Figure 2m 1 of 1 ▼ Part A If the gap between the plates is a = 1.46 mm, determine the maximum allowable pressure drop from A to B so that the flow remains laminar. Express your answer to three significant figures and include the appropriate units. Apmax=2060 μA Pa Submit Previous Answers Request Answer Provide Feedback * Incorrect; Try Again; 4 attempts remaining Next >

A solar water heater mounted on the roof consists of two flat plates. Water enters at A and exits at B. Assume the average temperature of the water is 45° C. (Figure 1) Figure 2m 1 of 1 ▼ Part A If the gap between the plates is a = 1.46 mm, determine the maximum allowable pressure drop from A to B so that the flow remains laminar. Express your answer to three significant figures and include the appropriate units. Apmax=2060 μA Pa Submit Previous Answers Request Answer Provide Feedback * Incorrect; Try Again; 4 attempts remaining Next >

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The pressure through a section of pipe is 23 PSI and the velocity of the fluid is 3 ft/sec. If the velocity was increased to 5 ft/sec, what would the pressure drop be?
1. Estimate the volume flow rate (gpm) in the pipe with a diameter of 50mm and a water velocity of 50m/s. 2. Determine the specific weight of air when the temperature is 1000F and the absolute pressure is 80psi.
Problem Consider a cylindrical pipe of length L and diameter D = 2R. The angle that the axis of the pipe forms with the vertical direction is a. Assume that when the fluid enters the pipe its velocity is uniform (i.e., it has the same value over the entire cross-section of the pipe) and equal to U in the axial direction. In the radial and angular directions, the velocity is zero. So, it is: 2 =0: v(r, 0, 2) = Ue, (1.1) Here v is the fluid velocity and e, is a vector of unit magnitude parallel to the coordinate axis z; furthermore, we have assumed that the pipe inlet is located at z = 0. Near the entrance of the pipe, the velocity profile varies in the axial direction. But after a certain entrance length, the profile becomes fully developed, no longer changing with z. The evolution of the velocity profile is sketched in Fig. 1, where, for clarity, the pipe inclination is not shown. The entrance length is denoted by L.. For z > L., the fluid velocity is no longer a function of the axial…
PROBLEM 2 Consider a firefighter who is standing on a ladder and spraying water with a hose into Chief Inspector Jacques Clouseau's (Figure 3a) third-story apartment. A diagram of the hose/nozzle used by the firefighter is shown in Figure 3b. Assume the nozzle has little effect on the flow in the hose and water in the hose/nozzle is incompressible. The temperature of the water in the hose is 15 °C. (a) Chief Inspector Jacques Clouseau investigating the cause of the fire in his apartment. water hose diameter=10cm outlet diameter=5cm Figure 3 个个个 outlet velocity=6ms¹ (b) Fire hose/nozzle used to extinguish the fire in Inspector Clouseau's apartment.
Given the 0.063 m length of the syringe. F=1N a. provide an equation to calculate its water flow rate if water is going to travel from a 0.063 m length of syringe with dextrose tube length of 0.5 meter to another 0.063 m syringe (see attached photo). The Inner diameter of the syringe is 0.02. While the inner diameter of dextrose tube is 0.003. b. provide an equation in order to calculate the maximum force or pressure that exerts in plunger in order to travel the water at its maximum speed.
Engine oil (n = 0.20 Pa·s) passes through a fine 2.00-mm-diameter tube that is 10.2 cm long. ▼ Part A What pressure difference is needed to maintain a flow rate of 4.4 mL/min ? Express your answer to two significant figures and include the appropriate units. ΔΡ = 4.76 Submit μA Provide Feedback Pa Previous Answers Request Answer ? X Incorrect; Try Again; 27 attempts remaining Next >
Heavy machine tool lubricating oil (ref. Appendix C applied fluid mechanics) is pumped through six rectangular slots in a heat exchanger (oil flows in the white rectangles in section view a-a) as shown below. You may assume that the oil flows through the heat exchanger with a constant temperature of 40°C. If the flow rate from A to B is 3 cm³/sec determine the Reynolds number for the oil flow. Is the flow laminar or turbulent?
Question A liquid flows through the horizontal pipe of varying cross section. Calculate the areas of the larger and smaller cross sections by measuring their diameters. Measure the speeds of the liquid in both larger and smaller cross sections. Calculate the liquid rates of flow in both sections. Calculate the ratio of the rates of flow. Comment if your result confirms the Conservation of Rate of Flow. Explain how you came up with your results. Diameter 1 (Big cross section) = 0.39 Radius 1 = 0.195 Area 1 = 0.1195 velocity 1 = 0.0986 Diameter 2 (Small cross section) = 0.2 Radius 2 = 0.1 Area 2 = 0.0314 velocity 2 = 0.1986
please answer question ASAP
Working for an engineering consultancy firm, your knowledge of fluid dynamics is required to design a new safety feature for a high-pressure air line in a factory. The air line takes the form of a cylindrical pipe of diameter 150 mm, which is designed to operate between 0.45 MPa and 0.76 MPa. At the end of the pipe a burs9ng disk is placed so that, if the pressure exceeds the maximum opera9ng pressure, the air is vented to atmosphere rather than over-pressuring the chemical reac9on vessel (Figures 4a and 4b). In this ques9on, you should treat the flow as quasione-dimensional and inviscid. The air in the surrounding atmosphere is at 101 kPa and 298 K. a) You have a choice of five disks which can withstand the following forces across them before burs9ng: 10.5 kN, 11.0 kN, 11.5 kN, 12.0 kN, 12.5 kN. Which of these burs9ng disks would you recommend, and why? b) Due to an over-pressurisa9on of the air line, the disk bursts at 9me t = 0. At what pressure in the air line will this occur? c)…
answer 2nd question
Question 1 A pipeline of length 2000 m and diameter 200 mm connects two water supply reservoirs together. (a) If the value of the frictional factor, f, for the pipeline is 0.02 then determine the flow in the pipeline when the head difference between the two reservoirs is 20 m. (b) If an increase in demand requires that the flow be increased by 40% then determine what length of the same diameter pipe is required to satisfy this demand if it is connected as shown in Figure 1. Assume that the friction factor for the new pipe is the same as the existing one. New pipeline 20 m