88) If the required casing tension is 150000 Ibf, what should be the designcasing tension? 33) The additive which is used to remove the calcium from the hard water is ;A) Soda ashB) Sodium carbonateC) Sodium borateD) Caustic soda

33)In order to remove the permanent and temporary hardness of water if calcium is present then…

Answered: A) Soda ash B) Sodium carbonate C)…

Engineering

Civil Engineering

A) Soda ash B) Sodium carbonate C) Sodium borate D) Caustic soda

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Lead poisoning is considered an occupational

Q: In titration for alkalinity (5.0 ml) of 0.02N Sulfuric acid is used to reach the phenolphthalein end…

A: Volume of water sample = 100 ml Volume of 0.02 N sulfuric acid to reach phenolphthalein endpoint = 5…

Q: H.W(2) – Lecture (4) Fill in the blanks: 1- In the hydration process of cement, the water in ---.…

A: ● Solution:- Here in this question we are talking about the cement and its fineness and the water…

Q: Bricks must be with . before use to decrease the soluble salts inside the bricks الجواب:

A: Given data Bricks related To be done Bricks related knowledge

Q: How many light drops of the tamper should be done for the fine aggregate into the mold in performing…

A: How many light drops of the tamper should be done for the fine aggregate into the mold in performing…

Q: reverberation time (RT)?

A: Reverberation time (RT) is the time required for the sound in a room to decay over a specific…

Q: It is also known as the vadose zone.

A: Vadose zone is the zone in which all pores of soil are empty that means no water is present in the…

Q: I have an equalization tank with the following dimensions: Tank Dimensions: Height: 5.15 meters…

Q: The sludge age 1. Is a measure of the time taken for sewage to stay in the bioreactor 2. Is one of…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: How the temporary hardness of water is removed? (A) by boiling (C) by zeolite process (B) by lime…

A: Option A:- By Boiling is the correct answer for the given question Temporary Hardness of water can…

Q: 36. In a white wash, after how many hours is dissolved gum added to the solution? A. O 24 hours B. O…

A: Answer :- Option a - 24 hours A fat lime is used to make white wash. In a large drum, fat lime is…

Q: An organic matter is degrading in a steady state complete mix type reactor following the firstorder…

Q: A sample is diluted to perform test 295 ml distilled water are added to 5mL sample to fill 300 ML…

Q: Which compound may lead to a rapid stiffening of the paste with a large amount of heat generation?

A: Solution: "The option marked in the above question asked, is wrong." The correct option of the…

Q: Q2: (12.5 Marks) Two-stage softening: A water with the ionic characteristics shown below is to be…

A: Step 1: 1. Draw the treatment units scheme The typical treatment units in a two-stage softening…

Q: Can you please help me to Sketch a Process Flow Diagram (PFD) for a Wastewater Treatment Plant…

Q: Problem 2. A reverse osmosis membrane has a kw values of 2.5-10 L/(m²-s-bar) and an average ks value…

A: Step 1:

Q: Which of the following statements is not true about acids? A weak acid is not dangerous and may be…

A: "The parent material is the soil deposited at the earth surface." This statement is incorrect.…

Q: Question: 1. Discuss the potential paths of formation of Ettringite, monosulfate, and calcium…

A: Ettringite and calcium and monosulfate aluminate hydrates are formed during the chemical reactions…

Q: An activated-carbon bed that is 12 ft x 6 ft x 2 ft deep is used in a benzene recovery system. The…

A: Solution; Given data; Depth of bed D = 2 ft Void fraction ε = 0.40 Gas viscosity µ = 0.047 lb/ft-hr…

Q: (c) Distinguish between UV and chlorine disinfection method for water treatment and then choose the…

A: Given data in question UV methodChlorination methodTo find out Which is more efficient by…

Q: 6. Backwashing is used in A. Filtration processes B. Ion-exchange processes C. Membrane processes D.…

A: Backwashing is used in membrane processes. Backwashing is used in reverse direction of flow. In…

Q: 5. The Pherric, New Mexico, groundwater contains 1.800 mg/L of iron as Fe*. What pH is required to…

A: Given:Groundwater has 1.800 mg/L Fe and desired concentration is 0.30mg/L

Q: 13- At any stage of hydration, the . ..represent that part of the gross volume which has not been…

A: We have to determine that which option among all given options is correct according to the given…

Q: A lime-soda softening plant treats a flow of 150 MGD, and the water has a hardness of 225 mg/ℓ as…

A: Answer (a) Calculation of pounds of quicklime required per million gallons We know that pounds of…

Q: Determine the pH of a solution that contains 2*(10^-4) mg/L of OH- (at 25 degrees)

Q: 36. In a white wash, after how many hours is dissolved gum added to the solution? A. O 24 hours В.…

A: White wash is a form of paint which is prepared from lime called as Fat Lime.

Q: is generally considered the most corrosive environment. D Acid solution O Alkali solution O Neutral…

A: Solution given in next step

Q: The second stage nitrification process is presented by the following equation Nitrobacter 2NO2+ 02…

A: 1.14 answer is c

Q: Draw a neat sketch of Activated Sludge Process and discuss the inter-relationship of control factors…

Q: How much bleaching powder is needed to chlorinate 5000l of water whose chlorine demand is 2 mg/l,…

A: Given: To chlorinate 5000 l of water. Whose chlorine demand is 2 mg/l The bleaching powder required…

Q: A treatment plant has been designed to achieve 99 percent inactivation of Giardia Lamblia using…

A: 99% disinfection Present temperature = 20oCNew temperature = 0.5oC

Q: a) criteria, hazardous (b) hazardous, criteria, (c) toxic, particulate (d) PM2.5, organic

A: Criteria air pollutants are air pollutants for which acceptable levels of exposure can be determined…

Q: 3-Moisture content of the slurry used in the wet process is. 2% b) 0.2% c) 40% d) 3% (b

A: Hi! Thank you for the question As per the honour code, We’ll answer one question since the exact one…

Q: .Consider a water at pH 6 that contains acetic acid. What is the fraction of acetate (CH3COO¯, the…

A: Given:- pH=6 To find:- fraction of acetate (CH3COO-) To find:- fraction of acetate relative total…

Q: 3. Problem 5-18 (modified), Davis and Cornwell, Introduction to Environmental Engineering, 6th Ed.:…

Q: 0 0 Influent- Influent Influent Anaerobic Aerobic Influent- Return activated sludge Aerobic Anoxic…

A: This question is related to the Environment Engineering from Civil Engineering. In this question ask…

Q: 8. If saturated paste extract EC, is 2 dS/m, then what is the osmotic potential y, of the water if…

A: Data Given: ECe = 2 dsmθ = 15%θs = 45% Asked: Osmotic Potential Ψs of water

Q: Condensation occurs when the temperature is the dew point temperature (Td). O less than or equal to…

Q: ADD lime No 20 mg/L Add Soda- NCH to be removed Yes Yes Is Mg 40 mg/L? IN (Mg2+ -40) 207 No ADD lime…

A: Given Ca= 80mg/litre Mg= 55mg/litre Hco3= 350mg/litre Total hardness= 80mg/litre as caco3 Carbonate…

Q: The initial concentration of acetic acid is 0.6mM and its concetration is 0.42mM after adsorption…

Q: Discuss the principle, construction, operation, uses, advantages and disadvantages of Evaporating…

Question

88) If the required casing tension is 150000 Ibf, what should be the design
casing tension?

33) The additive which is used to remove the calcium from the hard water is ;
A) Soda ash
B) Sodium carbonate
C) Sodium borate
D) Caustic soda

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Material structure and physical properties

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The purpose of heat treatment
I need the answer as soon as possible
Q3: Under which kind of industrial chemical process can you classify the designated treatment during petroleum refining? Why? Sulfur Sour Water H;s Recovery/ Tail Gas Unit(s) Gas + Refinery Fuel Sulfur Steam Stripper LPG, Butanes Light Naptha 3 Heavy 4 Exhaust Naptha Hydrotreater Crude Oil (de-salp Catalytic reformer 2 bene el Kerosene, Jet Fuel Oxidation Gas Crude distillation blending unit lOil Hydrotreater Diesel unit Steam Gas Oil Hydrocracker 1 Diesel ces Demulsifier Residuum Vacuum Distillation Unit Catalytic Cracking Unit Fuel Oil Gasor Refinery Fuel Petroleum Coke co2 Coker unit Hydrogen Synthesis Gas H2 Flares
9
Filtration is best suited for viscous liquids containing particulate matter. a.False b.True
11-10. An ion-exchange resin has a capacity of 1600 eq/m³. The manufacturer recom- mends that the resin be regenerated when 75 percent of its capacity has been utilized. The regeneration cycle takes I h for draining, regeneration, and flushing the bed. The contact time in the bed(s) is to be 10 min when one bed is out of service and one bed is being regenerated. The plant is to reduce the hardness of a flow of 7000 m³/day from 250 to 100 mg/L as CaCO3. Determine the total volume of resin required and the number of beds to be used. What is the frequency of regeneration which would be required?
Answer the question?
88 Building Construction Materials Baghdad University/Civil Engineering Dept. 1" stage Brick questions (lectures 4,5 & 6): QI/ Alkalis are harmful ingredient in clay bricks. How? Q2/ what is the effect of the following on clay brick: Silica, iron oxide, magnesia and lime. 03/ what are the states of Effloresce in clay bricks? Q4/ what are the types of brick? Q5/ the weight of an average of ten dry bricks are (2960 gm) and after 24 hours in water the weight of the same ten bricks is (3298gm) find the percentage absorption and within which class is this type according to the Iraqi standard No. 25 / 1988? Q6/ talk about the manufacture of bricks. Q7/ define the pigments used in sand-lime brick and give its mix proportion. Q8/ what are the properties of sand lime brick? Q9/ what does concrete brick constituent of and what is its mix proportion? Q10/ what are the harmful ingredient in clay bricks. Q11/ what are the properties of concrete brick? Q12/ qualify the following: - There is no…
4. Problem 5-16 (modified), Davis and Cornwell, Introduction to Environmental Engineering, 5th Ed.: Determine the concentration (mol/L) of hydroxide that must be added to an aqueous solution to produce a concentration of 0.50 mg/L copper if the starting concentration is 3.5 mg/L copper. The solubility product for copper hydroxide (Cu(OH)2) is 2.2 x 10-20 mol/L. What is the resulting solution pH?
Problem 8 Given L0,mix=12 mg/L, DO mix=DOsat=11.33 mg/L, kd=0.3 d-1, and kr =0.4 d-1, find the following: (a) Initial oxygen deficit (Do) (b) Critical time on the oxygen sag curve (tc) (c) Critical deficit (Dc)
write the limitations of revers osmosis water treatment Techonolgy
A 2-tank Step Aeration Activated Sludge (SAAS) system has the following characteristics: V1 V2 Q Waste Recycle Oxygen demand (L) (L) (L/min) Ratio Ratio of Cells 500,000 450,000 100 0.45 0.5 1.2 Xv1 Xv2 Xd1 Xd2 SO S1 S2 Xrv Xrd (mg/L) (mg/L) (mg/L) (mg/L) (mg/L) (mg/L) (mg/L) (mg/L) (mg/L) 1500 ☐ 14 1400 200 150 150 10 2 2000 1000 1. What is the mean cell residence time and hydraulic residence time in days? 2. Write the mass balance equation for required oxygen in tank #1. 3. What is the oxygen requirement for tank #1 in kg/day? (equation will be in units of mg/min)