A small object is initially at rest at the top of a large solid sphere that is fixed on the ground. The smallobject then begins to slide along the surface of the large solid sphere, without friction.V₁ = 0RIPart (a) Find the angle at which the small object loses contact with the large solid sphere.Part (b) Find the maximum horizontal distance traveled by the small object before it hits the ground. Take(xi, y₁) = (0,2R) as the coordinates for the top of the large solid sphere.

Answered: Image /qna-images/answer/c671f3ac-bde4-41e7-b894-dfc35eec4c4d.jpg

Answered: A small object is initially at rest at…

Similar questions

A drag chute must be designed to reduce the speed of a 1171 kg dragster from 342 km/hr to 80 km/hr in 4 seconds. Assume that the drag force is proportional to the velocity (kv). a) What value of the drag coefficient k is needed to accomplish this? kg · s? (Leave an exact answer.) m2 k = b) How far (in meters) will the dragster travel in the 4-sec interval? d = meters. (Round to the nearest meter) Question Help: O Message instructor Submit Question
Consider a 25-kg block on a frictionless inclined plane held in place by a steel cable as shown in the figure. The cable is parallel to the surface of the incline. What is the magnitude of the tension on the steel cable? 25 kg 30° 212 N O 245 N O none of the choices O 123 N O 458 N
A Box is placed on a 40° slope with a coefficient of friction of 0.30. The box starts approximately at 6.0m off the ground. It slides onto a horizontal part with a coefficient of 0.45. How far does it slide along this part?
Two blocks of mass m, = 10 kg and mg = 5 kg are connected by a massless string that passes over a pulley as shown in the figure. The system is in static equilibrium. There is friction between m, and the inclined surface (u.-0.4), Neglect the friction between the string and the pulley. Determine the tension in the string. 10 kg 5.0 kg 37 65.35 N () 147.0 N 98.0 N 49.0 N O 52.3 N
The figure shows the configuration of two identical bricks. In case 1 the bricks are placed end to end. In case 2 the bricks are stack on top of each other. What can you say about the kinetic friction when the bricks are pushed across a tabletop with constant speed?
In the figure, a rectangular slab of slate rests on a bedrock surface inclined at angle = 25.6°. The slab has length L = 43.4 m, thickness T = 6.23 m, and width W = 13.6 m, and 1.0 cm³ of it has a mass of 3.2 g. The coefficient of static friction between slab and bedrock is 0.351. (a) Calculate the component of the gravitational force on the slab parallel to the bedrock surface. (b) Calculate the magnitude of the static frictional force on the slab. By comparing (a) and (b), you can see that the slab is in danger of sliding. This is prevented only by chance protrusions of bedrock. (c) To stabilize the slab, bolts are to be driven perpendicular to the bedrock surface (two bolts are shown). If each bolt has a cross-sectional area of 6.42 cm² and will snap under a shearing stress of 3.57 × 108 N/m², what is the minimum number of bolts needed? Assume that the bolts do not affect the normal force.
A toy car is rolling down the ramp as shown in the figure. The car's mass is m = 1.6 kg and the ramp makes an angle of θ = 12 degrees with respect to the horizontal. Assume the car is rolling without friction. A) Using the coordinate system specified given an expression for the acceleration of the car in the terms of θ, g and the unit vectors i and j. B) What is the magnitude of this acceleration in m/s^2
The chain binder is used to secure loads of logs, lumber, pipe, and the like. If the tension T₁ is 3.4 kN when 0 = 33°, determine the force P required on the lever and the corresponding tension T₂ for this position. Assume that the surface under A is perfectly smooth. Assume a = 100 mm, b = 460 mm. T₁ Answers: P = T₂ = i i 9 A B KN 2 KN 2 b Topoces T₂
Learning Goal: A man wishes to spin a merry-go-round in the x-y plane centered at the origin (0.000, 0.000, 0.000). (Figure 1) Because he must pull upward and cannot stand on the merry-go-round, he must apply a force in the direction of the unit vector u =(-1/3)i + (2/3)j + (2/3)k. He pulls with a force F= 324 N from point A [(1.10, 1.40, 0.000) m]. Figure 1 of 1 4
A block of mass 4.6 kg is sliding down a ramp with an initial speed of 1.5 m/s. The ramp is inclined from the horizontal by an angle theta = 34.9 degrees and the coefficient of kinetic friction is uk = 0.73. What is the magnitude of the displacement of the block along the ramp from the initial time until it stops?
A woman pushes a 10.0 kg box across a horizontal floor with a constant force of magnitude 40.0 N directed at an angle of -25° with respect to the positive x-axis. The box moves horizontally to the right. At the origin (x=0) the box has an initial speed of 4.00 m/s and the woman pushes it to a location ofx=3.00 m. what is the force of the woman? what is the force of gravity? what is the normal force of the floor?
Time left 0:20:32 An amusement park in Dubai has a ramp which is frictionless. A child drops a smooth object and it slides down the ramp and comes down through a height 4 m. What distance is necessary to stop the object on the flat track if the coefficient of friction is 0.4? h. Answer:

SEE MORE QUESTIONS