A small grinding wheel is attached to the shaft of an electric motor which has a rated speed of 3600 rpm. When the power is turned on, the unit reaches its rated speed in 5 s, and when the power is turned off, the unit coasts to rest in 70 s. Assuming uniformly accelerated motion, determine the number of revolutions that the motor executes (a) in reaching its rated speed, (b) in coasting to rest.

Q: The rotor of a gas turbine is rotating at a speed of 6000 rpm when the turbine is shut down. It is…

A: As for the given question we have determine (a) the angular acceleration, and (b)number of…

Q: Given that: 1) The length of L4 of link AB is 1 m. 2) The length of L1 of link CD is 0.5 m. 3) The…

A: GIVEN:- The length of link AB: L4=1m The length of link CD: L1=0.5m The length of link: L3=1m The…

Q: The turning-moment diagram for an engine, which has been drawn to scales of 1 mm to 50 Nm and I mm…

A:

Q: A belt moves between the pulleys of the crankshaft of the air conditioning fan and over the idler…

A:

Q: In a mechanism that is a combination of a four-bar mechanism and a slider-crank mechanism. Slider A…

A:

Q: 4. A bullet's speed can be found by shooting it through two rotating paper discs mounted a distance…

A: The values are

Q: The rotor of a gas turbine is spinning at a speed of 6,300 rpm when the turbine is deactivated. It…

A: Rotor initial speed Ni = 6300 rpm Rotor final speed Nf = 0 rpm ( rotor reaches rest )Time taken t =…

Q: A connecting rod is supported by a knife-edge at point A. For small oscillations the angular…

A:

Q: A connecting rod is supported by a knife-edge at point A. For small oscillations the angular…

A: Given data:To find:Angular position when t = 3 sec.

Q: A connecting rod is supported by a knife-edge at point A. For small oscillations the angular…

A: maximum angular velocity when t = 2sec.

Q: Consider (Figure 1). For a short period of time, the motor turns gear A with a constant angular…

A: Jskak

Q: Determine the torque needed to bring a turbine whose moment of inertia of 60 slugs-ft² to rest in…

A: Given that, Moment of inertia  = I= 60 slugs-ft2 Initial speed = Ni=764 rpm Final speed = Nf=0 rpm…

Q: 2. Tid the percentage mercase in specu, in the Danis rise by 20 min. [Alls. 370] A Porter governor…

A: Ball 1 mass, m=3 kg Ball 2 mass, M=15 kg Arm length, BP=BD=200mm =0.2m Minimum radius of rotation,…

Q: Q3: The crank of a slider-crank mechanism rotates counterclockwise at a constant speed of 300 r.p.m.…

A: consider the arrangement of mechanism with itsgiven dimensions and their namings       NBD=300…

Q: Both 15-cm-radius wheels rll without slipping on the horizontal surface. Knowing that the distance…

A: For wheel 1, Let the speed of wheel 1 be ω1Angular acceleration of wheel 1 be α1As wheel us pure…

Q: Given that: 1) The length of L4 of link AB is 1 m. 2) The length of L1 of link CD is 0.5 m. 3) The…

A: GIVEN:- The length of link AB: L4=1m The length of link CD: L1=0.5m The length of link: L3=1m The…

Q: For a short time, gear A of the automobile starter rotates with an angular acceleration of a =…

A:

Q: 1. Draw the complete and clear FBD of the block C. Indicate two sides of the FBD with all forces and…

A:

Q: Derive Lagrange’s equation of motion from Newton’s laws.

A: Lagrange's equation of motion is a powerful mathematical tool that can be used to describe the…

Q: If gear A rotates with a constant angular acceleration of aA = 89 rad/s2, starting from rest,…

A: Introduction If two or more gears are installed on the same shaft in a compound gear configuration,…

Q: A child is playing with a tyre of radius 0.5m. She accelerates it from 5 rpm* to 25 rpm in a time of…

A: The linear acceleration of the tyre is 0.07 m/s2. Therefore, option (d) is correct answer.

Q: quantity of oil into the well pipe, and he column of oil is then lifted to obtain a discharge into…

A:

Q: magnitude of the absolute velocity

A: Given; A shell is fired from a cannon. At the instant the shell is just aboutto leave the barrel.Its…

Q: A cylinder rolls without slipping between two moving plates C and D. The radius of the cylinder is…

A:

Q: Links AB, BC and CD are connected as shown, with link AB having an initial angular velocity and…

A: For link AB VB=ωAB×rAB=3×1 =3m/saB=αAB×rAB-ωAB2×rABaB=-6k×1i-32×1iaB=-9i-6jm/s2

Q: A disc rolls without slipping. The magnitude of the angular velocity w= 1.0 rad/s, the angular…

A:

Q: A volleyball player spikes the ball. At the instant that she begins to extend her shoulder to bring…

A:

Q: 1. At the state shown, the disk rotates about O in the counterclockwise direction at 4 rad/s. This…

A:

Q: The rotor of a gas turbine is turning at a speed of 6,600 rpm when the turbine is turned off. It is…

A:

Q: b) A tensile test was carried out on a mild steel test-piece having a diameter of 12mm and a gauge…

A: 2b) Given: Gauge Length (L)=88mmDiameter of the bar (D)=12mmLoad at limit of proportionality…

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A: N=600 rpmt=4s

Q: Y AB = 2.4 cm 300° BC = 8.3 cm CD = 3.1 cm BE = 3.1 cm AT EC = 9.6 cm EF = 4.8 cm 2)

A: From the given data,

Q: The ball shooting mechanism from a pinball machine is shown. The motor provides the torque shown.…

A:

Q: The rated speed of drum B of the belt sander shown in Figure 4 is 2400 rpm. When the power is turned…

A: There are two types of acceleration associated with circular motion one is tangential acceleration…

Q: The rotor of a gas turbine is rotating at a speed of 6900 rpm when the turbine is shut down. It is…

A:

Q: The rotor of a gas turbine is spinning at a speed of 5,700 rpm when the turbine is deactivated. It…

A: First we will calculate the initial angular velocity from given rom and then calculate the angular…

Q: A simple friction drive consists of two disks A and B. Initially, disk B has a clockwise angular…

A: Given Data: Initial angular velocity of disk B ωiB=590 rpm=590×0.10472=61.7848 radsec Disk B stops…

Q: magnitude of the normal acceleration

A:

Q: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to…

A:

Q: What do you understand by the principle of conservation of energy? Expiain how the principle applies…

A: i) Energy Conservation Principle states that " states that energy is neither created nor destroyed.…

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.