A small block with a mass of 0.0900 kg is attached to a cord passing through a hole In a frictionless, horizontal surface. The block Is originally revolving at a distance of 0.40 m from the hole with a speed of 0.70m/s. The cord is then pulled from below, shortening the radlus of the circle in which the block revolves to 0.10 m. At this new distance, the speed of the block is observed to be 2.80 m/s. What is the tension In the cord In the final situation when the block has speed v-2.80m/s? Option1 Option2 Option3 Option4 Option5 7.1 N 0.11 N 6.5 N 0.12 N 2.11 N

A small block with a mass of 0.0900 kg is attached to a cord passing through a hole In a frictionless, horizontal surface. The block Is originally revolving at a distance of 0.40 m from the hole with a speed of 0.70m/s. The cord is then pulled from below, shortening the radlus of the circle in which the block revolves to 0.10 m. At this new distance, the speed of the block is observed to be 2.80 m/s. What is the tension In the cord In the final situation when the block has speed v-2.80m/s? Option1 Option2 Option3 Option4 Option5 7.1 N 0.11 N 6.5 N 0.12 N 2.11 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A ball of mass m is sliding in a frictionless tube of total length 4L as shown below in the figure. The tube is rotating at a constant angular velocity, w. Initially, the ball is at rest relative to the tube at point A at r = Lêr. (a) Derive the velocity and acceleration of the ball. (b) What is the velocity vector when the ball exits the tube? e. W r n ոլ m₂ m eo er
The weight of a 100 kg mass body at a given elevation is 0.9804 kN. If the variation from the standard gravitational acceleration is 0.004 mps² per 1000 m, determine the elevation at this point.
A drum is made to revolve about its centre by a falling mass as shown. Calculate the velocity of the falling mass and rotating drum when the mass descends 10 m with no frictional losses. Also calculate the energy gained by the drum. DRUM k = 0.3 m M = 15 kg MASS M= 12 kg Figure Q2a R =.0.4 m r = 0.2 m
In the figure, the 2-kg disk is attached to an elastic cord on a smooth surface, and pushed from rest with the velocity shown. The cord has a “spring” constant of k = 20 N/m, and is initially unstretched. What will its rate of stretching and the speed of the disk be when the cord has been stretched 0.2 m?
A 60-g model rocket is fired vertically. The engine applies a thrust P which varies in magnitude as shown. Neglecting air resistance and the change in mass of the rocket, determine (a) the maximum speed of the rocket as it goes up, (b) the time for the rocket to reach its maximum elevation.
2. The 200 gram toy car will be compressed against the spring and released to send it around the loop which has diameter of 60 cm. Determine minimum required spring compression to maintain contact with the track for the entire loop. First use kinetics to determine minimum velocity at the top of the track, and then apply conservation of energy. Spring constant is 400 N/m. -------
A block of mass 2.40 kg is placed against a horizontal spring of constant k = 825 N/m and pushed so the spring compresses by 0.0750 m. HINT (a) What is the elastic potential energy of the block-spring system (in J)? (b) If the block is now released and the surface is frictionless, calculate the block's speed (in m/s) after leaving the spring. m/s
Determine the acceleration produced in a body of 20 kg mass when it is acted upon by a force of 200N. Use D’ Alembert’s principle.
When it hails, each golf ball-sized chunk of hail rained down with a mass of 0.025 kg mass and impacted my car with a velocity of 400 m/s. The hood of the car is made out of 1040 steel. The modulus of elasticity is 207 GPa, the YS is 490 MPa, and the UST is 590 MPa. A. Determine the amount of energy (or work) that the steel hood of my car could absorb before being Plasticly deformed. Assume that the cross-sectional area impacted by the hail is 0.0005 m2 and that the thickness of the steel is 0.005 m. B. Determine the amount of energy (or work) that the steel hood of my car could absorb before being fractured. Assume that the cross-sectional area impacted by the hail is 0.0005 m2 and that the thickness of the steel is 0.005 m.
r = 1 A A 1-kg collar has a velocity of 9 m/s when to the right when it is at A. It then travels along the circular smooth guide of radius r+l B 199-cm from A, to B, a quarter of circle right-down to A. The collar is also connected to a spring, attached on its right-hand side to the collar and its left- hand side to a point, the same height as B
The figure depicts two pucks on a frictionless table. Puck 2 is four times as massive as puck 1. Starting from rest, the pucks are pushed by two equal forces. 1-Which pucks will have the grater kinetic energy upon reaching the finish line? 2- Which puck will reach the finish time first ?
A vertical take-off and landing aircraft has a mass of 9000 kg. A constant upward thrust of 100 kN is applied to it. Determine the vertical distance it will travel when it reaches the velocity of 10 m/s. Clearly write down here what principle or law you use in this problem. Draw FBD of the aircraft here.