(a) Sketch an influence line diagram for reaction force at B and moment at C. Treat B as a pin and A as a roller. (b) Suppose the beam supports a uniform dead load of 0.8 k/ft and a single live concentrated force of 8 kip. Determine the maximum positive moment at C. (Answer to check: 35 k-ft) B 10 ft - 10 ft 15 ft

(a) Sketch an influence line diagram for reaction force at B and moment at C. Treat B as a pin and A as a roller. (b) Suppose the beam supports a uniform dead load of 0.8 k/ft and a single live concentrated force of 8 kip. Determine the maximum positive moment at C. (Answer to check: 35 k-ft) B 10 ft - 10 ft 15 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Assuming A is fixed. Draw the influence line for shear at B. What is the value of the influence diagram at A? 2 m 1m
Using the Muller-Breslau principle, sketch the appropriate shape of the influence line for the shear just to the right of support B. Show where to place moving distributed live load of 2 kN/m for the maximum positive effect. Assume A is a pin and B and C are rollers. В D 10 m -5 m -5 m
How about numbers 21,22,23,24,and 28?
Illustrate the Influence Line and calculate the maximum negative live shear at point C in kN subjected to 7 kN/m uniform live load, 90 kN live load and beam mass of 18 kg/m. Set L= 4 m, support A is pin and support B is roller. |A B L 3 m -1.5 m→
A uniform live load of 3 kN/m and a single live concentrated force of 45 kN can be placed on the haunched girder. Illustrate the Influence Line and determine the maximum live negative moment at B. 6 m 3 m Use the editor to format your answer
1. The beam supports a uniform live load of 80 lb/ft and a live concentrated force of 500 lb. Assume A is a pin and B is a roller. Draw the influence diagram of reaction at B, shear @ D and C, and moment at C and D. Determine , a. The maximum positive live vertical reaction at B b. The maximum shear that can be developed at C c. The maximum shear that can be developed at D d. The maximum live moment that can be developed at C. e. The maximum live moment that can be developed at D. 10 ft 10 ft- 15 ft
Use the Müller-Breslau principle to sketch the influence lines for the vertical reaction at A, the shear at D, and the moment at B.
Use analytical method and Muller and Breslau principle L1 = 3m L2 = 9m L3 = 3m
Please answer the ff in neat & complete solution Influence Lines Problem: Construct the influence lines for the support reactions, and then use them to obtain the influence lines of bending moments and shear forces at point B for a statically determinate beam shown below. Use the equilibrium equation.
Illustrate the Influence Line and calculate the maximum positive live shear at point C in kN subjected to 7 kN/m uniform live load, 90 kN live load and beam mass of 16 kg/m. Set L = 4 m, support A is pin and support B is roller.
The beam sown in Figure 1 is subjected to uniform live load of 3.2 kN/m and a dead load of 2.5 kN/m and a single live load of 80 kN. Determine: a. The influence line for moment at E. b. The influence line for shear at E. c. The maximum positive moment created by these loads at E. d. The maximum positive shear at E. Assume A and C are roller, B is a short link, D is a pin. |B E 4 m + 4m 3 m 3 m Figure 1