A single-phase transformer rated 55 KVA is connected to 400/220 V,49.5HZ supply, has an efficiency of 98% at full load. If the terminal voltage on full load is 205 V. Determine the % voltage regulation and output frequency. % Voltage Regulation Frequency

Q: R E H₁ G₁ H₂ G₂ G₁ G3 + C

A: Given: Block diagram of a control system. To find: Transfer function and error ratio using block…

Q: Solve using tinkercad cricuit design

A: The given logic diagram can be implemented and the output can be verified by using the truth table…

Q: = x³y²dy 3 ædy – ydæ solve the differential equation

A:

Q: 01(1) 18 N-m-s/rad 1 N-m-s/rad T(1) 02(1) $ kg-m2 3 kg-m2 3 N-m/rad 9 N-m/rad (a)

A: the answer is,

Q: (c) Find the closed-loop transfer function, C(s)/R(s) for the system shown in Figure Q3 using block…

A:

Q: Q2-which one is preferred AM-SSB or AM-DSB ? and explain why.

A: The explanation is as follows.

Q: The number of complex multiplications needed to find 4-point circular convolution using DFT method…

A:

Q: (1) F(A,B,C,D) = AC' D' + A'C + ABC + AB'C + A'C'D' (2) F (A, B, C, D) = E(0, 6, 8, 13, 14) +…

A: Find SOP &POS expressions using k maps for the given functions ?

Q: Q 5. (a). Apply substitution method and solve dx.

A: Given  ∫1e2x-9 is solved using substitution method

Q: and . . are. . :8 considered exponential .functions in MATLAB

A: Diag is inbuilt function used in MATLAB to create a diagonal matrix All the elements other than…

Q: R E H₁ G₁ H₂ G₂ G₁ G3 + C

A:

Q: Q.1 Classify the following wheather signal or system: Mobile phone Electric circuit Current Radio…

A: Since we have been authorized to answer only up to three sub parts. So,we''ll answer the first three…

Q: (B) Show the minimized POS for the following using K - map: F (A, B, C, D) Il (MO, M2, M4, M6, M7,…

A: Given maxterm. FA,B,C,D=∏M0,M2,M4,M6,M7,M8,M10,M12

Q: Which of the following is not a characteristic of the N-R method? Initial estimates must be close to…

A: first we will list the characteristics of Newton rhapson method to answer the given question.

Q: (A,B,C,D) = M0 + M1 + M4 + M5 + M6 + M8 + M9 + M12 + M13 + M14

A:

Q: A Not Secure math.webwork.rochester.edu/webwork2_. Previous Problem Problem List Next 1.e 10 -12 12…

A: Explanation: “Since you have posted a question with multiple sub-parts, we will solve the first two…

Q: Reduce the following block diagram H R(s), Y (s) G G G2 G, H H, H

A: Transfer Function The Transfer function can be defined as with Zero initial condition, the ratio of…

Q: Write a MATLAB function and testbench to obtain the first 10 elements of the following differenc…

A: GIVEN:               yn=0.5yn-1+xn where,   x0=1  FIND: write a MTLAB function to obtain first 10…

Q: Rind and draw the equation use k-moPs B. す

A: Method to find equation using k-map Observe the input and number of variables Mark in Table Circle…

Q: Circuit analysis using phasor/impedance, complex power calculation: A three-phase RLC circuit is…

A: For a three-phase RLC circuit, the following information is given:base parameters: Sb=100 MVA,…

Q: 5. A superheterodyne receiver is to tune the range from 4-10MHZ, with an IF of IMHZ. The ganged…

A: Since you have posted a question with multiple subparts, we will solve the first three subparts for…

Q: Please answer all subparts and in typing format please all subparts is compulsory

A: we need to write first order mathematical models for the given circuits.

Q: 1. The dlagram shows the maln window (perlod) of a perlodlc functlon In terms of constants a and b.…

A: The equation for the shown diagram will be  x(t)=abt             0⩽t<bx(t)=0…

Q: A possible solution for a first and second order derivatives have the same form expressed as a. At?…

A:

Q: error ratio usinf block diagram

A: Given: Required: Error ratio using block diagram reduction technique.

Q: Find the control ratio, C(s)/R(s) for the system given below using Mason’s Rule.

A: In this question We need to determine the tranfer function using the Mason gain formula.  We know…

Q: Xsin x + e* b. (D³ + 2D - 4) (e

A:

Q: Using the Routh's criterion, determine the stability of the closed-loop system that has the…

A: Given data : Characteristics equation,   S6+2s5+5s4+8s3+8s2+8s+4=0

Q: This is a practice question from my Signals and Systems course in my Electrical and Computer…

A: a) If you find the solution doubtful or doesn't match with your answer provided, or you feel that I…

Q: Determine C/R, for the system given H3 R2 R G2 G, H

A:

Q: 2. Determine C/R, for the system given R2 R G2 Gs H H

A: The solution is given below

Q: Consider the signal x(t) = 2 sinc(6t + 3). the output y (t) = (x *h )(t) when x(t) is passed through…

A: The input signal is given by⇒x(t)=2sinc(6t+3).The impulse response of a filter is given…

Q: ask z Show that the LRC circuit given below can be described by the differential equation L d²i + R…

A: In this question, we need to determine the current i(t) of the given system. Where

Q: Q1/ Reduce the following block diagram

A: The given block diagram can be reduced by using the block diagram reduction techniques.

Q: Determine the exact solution of the following differential equation y = 2 - y at y(0) =1. So the…

A:

Q: Q5) Determine the following: A. find the equation of the following circuit in the figure Q5A, and…

A: We need to find out simplify expression for given logic circuit . And we need to find out simplify…

Q: Subtraction of the following numbers by using the 2's complement 1001 - 110101 has 101100 as a…

A: