A single phase 220-V shunt DC motor has armature winding resistance is 0.2 2, the field winding resistance is 55 2 , and the brush voltage drop is 3 V. The motor operates at rated load at shaft rotation speed of 1500 rpm and draws a full load line current of 44 A at 220V. The rotational losses are 300 W. Determine the following: The field current I; The armature current I, Generated voltage E. Developed power in kW ,Developed torque in N-m Output power

A single phase 220-V shunt DC motor has armature winding resistance is 0.2 2, the field winding resistance is 55 2 , and the brush voltage drop is 3 V. The motor operates at rated load at shaft rotation speed of 1500 rpm and draws a full load line current of 44 A at 220V. The rotational losses are 300 W. Determine the following: The field current I; The armature current I, Generated voltage E. Developed power in kW ,Developed torque in N-m Output power

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Power systems quality
te) oblain the closad loop frasshr hunchan CbR) by using Mason's lormula fy the sylan belows GE G3 Gy G5
TOPIC: STABILITY Subject to a step input, the voltage drop across the resistor took 696.3103us to reach 13% of its steady value from rest. Determine the time (ms) needed to reach 90% of its steady value from 10% Determine the time (ms) needed to reach 80% of its steady value from 20%
Find the value of the load resistance for maximum power transfer
Show your detailed soln please
Write down at least three reasons which cause difference between R1 (R2) and R = Vmes/imes values in the below table?
Please someone solve this two questions
use junction and loop rule also use gauss elimination
W1 A 1 IL Tr1 AC Supply V V w2 12 Tr2 use double range voltmeter Fig.(1)
VDD- 10 Velt 106 ID2 I07 Assume the following: (a) M1 and M2 are matched (b) = 0 for all MOSFETS (c) L identical for all FETS. (d) ID2 = 50 µA. (e) W1=W2=W3=W6=W8 (f) W4=W5=2 x W2 (g) W7=3 x W8 (h) Except for W/L ratios establishëd by the photolithography design, the fabrication process is the same for all FETS. Pay attention to sign convéntions! Provide values for: ID3 ID4 ID7 ID5 = drain circuit for M5! (Trick question. Careful-look at the
A K- type thermocouple is used to measure the temperature in a heating process. The length of the bare material is 110mm and thickness is 1mm. Find the time constant of the bare material. Type of Thermo-coupleMaterial K ( W/m-k) Q (kg/m³)s (J/Kg- oc) Iron- Constantan 46 8535 345 K Kromel- Alumel 35 8738 380 T Copper- Constantan 160 8902 316 E Cromel - Contantan 33 8825 336 N Nicrocil- Nisil 34 8702 376 B Pt(30%)Rhodium - Pt(6%)Rhodium 19 15718 56 R Platinum(13%)Rodium - Platinum 55 16628 99 Platinum(10%)Rodium - Platinum 52.9 16745 99 Time constant of the bare material is, T=
PLZ LABEL ALLL CURENTS