A simply supported rectangular concrete beam having a width of 280 mm and aneffective depth of 500 mm. The beam is reinforced for tension only with a steel area of4,000 mm?. Given: f'. = 25 MPa, and fy = 400 MPa. Reference Code: NSCP 2015.%3D%3D1. Determine the depth of compression block (mm).2. Determine the ultimate moment capacity of the beam section (kN-m).3. Determine the uniform ultimate load (kN/m) that the beam can carry in asimple span of 6 m.

Answered: Image /qna-images/answer/f9edbc5e-61c9-4c75-b99c-79de3b4d7a10.jpg

A simply supported rectangular concrete beam having a width of 280 mm and an effective depth of 500 mm. The beam is reinforced for tension only with a steel area of l area 4,000 mm?. Given: f'. = 25 MPa, and fy = 400 MPa. Reference Code: NSCP 2015. %3D 1. Determine the depth of compression block (mm). 2. Determine the ultimate moment capacity of the beam section (kN-m). 3. Determine the uniform ultimate load (kN/m) that the beam can carry in a simple span of ó m.

A simply supported rectangular concrete beam having a width of 280 mm and an effective depth of 500 mm. The beam is reinforced for tension only with a steel area of l area 4,000 mm?. Given: f'. = 25 MPa, and fy = 400 MPa. Reference Code: NSCP 2015. %3D 1. Determine the depth of compression block (mm). 2. Determine the ultimate moment capacity of the beam section (kN-m). 3. Determine the uniform ultimate load (kN/m) that the beam can carry in a simple span of ó m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the axial load capacity ØP mar of the column cross-sections shown below. n,max f. = 4,000 psi, f,= 60 ksi, Ast = 8#9=8.0 in². D= 24 in.
A) Determine the shape factor and the Fully Plastic Moment (Mp) for the shaded symmetrical hollow rectangular beam section shown below. Assume the yield stress Oy =275 N/mm². B) If two plates of width 250 mm and thickness equal to 't' mm is connected (fabricated) at top and bottom (one plate on each side) for the given section, then what is the improvement in the fully plastic moment(Mp) of the section. C) If this revised fabricated section is now rotated by 90 degrees, what is its effect on the shape factor of the section? 200 mm. 50 m 100 ma 400 t- 10mm Note Take the value the 't' as equal to the last two digits of your studentid. If the last two digits are zero then take timm
A. Calculate the permissible moment capacity of the doubly-reinforced beam shown: Use f'c = 28MPa and fy = 415 MPa. A's = 1850 mm² A₁ = 4820 mm² 250 O ↓ 80 mm 620 mm 700 mm B. Using the same problem above, determine the permissible moment capacity if the compression reinforcement is removed and the depth (d) of the beam was reduced to 500mm. C. Using the same problem above but with the compression reinforcement removed and depth reduced to 500mm, determine the amount of tension steel (As) that will result in an under- reinforced condition (steel yields) type of failure. Express answer in mm2 Open in Acrobal Activate Windows Go to Settings to activate Window
A simply supported rectangular beam of length L has a width of b and an effective depth of d. Compression steel bars are placed at a distance d' from the extreme concrete compressive fiber. The beam supports service dead loads of wD and wl, respectively. Use fc'= 28 MPa and fy = 420 MPa. For the reinforcements, use 4 20 mm tension steel bars and 4 10 mm compression steel bars. b= 390 mm d= 615 mm d'= 165 mm L= 5.85 m Wd= 27.79 kN/m WI= 32. 25 KN/m Questions 1. Calculate the height of the neutral axis measured from the extreme compression fiber. 2. Calculate the strength reduction factor for the given beam. B. Calculate the design moment for the given beam.
ANSWER ONLY AC BC CDwrong answer gets downvote so double check the answer cause it will be input in the system
Complete solution pls. Tysm!
PLEASE INCLUDE COMPLETE FIGURES
1. A rectangular reinforced concrete beam has the follawing properties: Beam Span, L 6 m Beam width, b = 320 mm Effective depth, d = 640 mm Concrete strength, fc 25 Mpa Reinforcing steel strength, fy 200 MPa a. Compute the (Vanominal shear strength provided by the concrete. b. Compute the (V.) shear capacity of stirrups if it carries a Vu = 200 KN at critical point c. Compute the spacing of stirrups using 10 mm diameter rebar
Reinforce Concrete Design Determine the design moment capacity of the reinforced concrete beam shown inFigure 1(a) if it is reinforced with 4-28-mm diameter in tension and 2- 16-mmdiameter in compression. Use f’c = 21 MPa, fy = 276 MPa and effective cover of 50 mm for top and bottom bars.Assume the load W to be ultimate. Neglect weight of beam.
Title: Design of Beam in Flexure (WSD Method) PROBLEM: Design the beam to resist the loads shown. Take fc = 9 MPa, fs = 124 MPa, n = 11, bar diameter = 20 mm. Take b = d/2. Use WSD method. As (Gomm 20 KN lo Ka/m 8 KN/m 3m
Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 13 MPa. Answer must be in mm. Given: a = 1 m, b = 3 m, c = 2 m, P = 6 kN, and w = 3 kN/m. P kN cm w kN/m (not scaled) 250 mm am b m b. R1 R2
Situation #3: Given is a rectangular beam having the following parameters; d = 490 mm d' = 60 mm b = 300 mm fc' = 27.6 MPa fy = 276 MPa Mu = 620 kN.m %3D 10 نقاط Compute for the required steel 3.1 area in the compression side إجابتك ibäi 12 Compute for the required steel 3.2 * area in the tension side