A simply supported beam W 360x134 with a span length of 15 m is laterally supported at its ends and is subjected to the following service loads: DL = 6 kN/m (including the weight of the beam) LL = 15 kN/m If Fy = 345 MPa, check if the Beam is adequate for Shear. Properties: A = 17,100 mm2 h = 290.08 mm tw = 11.2 mm d = 356 mm CIVIL ENGINEERING- STEEL DESIGN

A simply supported beam W 360x134 with a span length of 15 m is laterally supported at its ends and is subjected to the following service loads: DL = 6 kN/m (including the weight of the beam) LL = 15 kN/m If Fy = 345 MPa, check if the Beam is adequate for Shear. Properties: A = 17,100 mm2 h = 290.08 mm tw = 11.2 mm d = 356 mm CIVIL ENGINEERING- STEEL DESIGN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam is simply supported and has a span of 12 m. The beam is a W33×240 with Ey=345 MPa. Compute the allowable (ASD) and ultimate (LRFD) uniformly distributed load that can be safely carried by the beam including its weight: A. If the length of the beam is 14m and the compression flange has lateral supports only at its ends and the midspan. Express your answer in N/m. (ASD) B. If the length of the beam is 14m and the compression flange has lateral supports only at its ends and the midspan. Express your answer in kN/m. (LRFD)| (Ctrl) Properties of W33×240: Weight = 3.51 kN/m tw = 21.08 mm x = 352.54 mm A = 45,548 mm? Ix = 5,660.75 × 10® mmª ry = 92.34 mm d = 850.9 mm ly = 388.34 × 10® mm Jc = 14.51 x 106 mm* bị = 402.97 mm Sx = 13,322.68 × 10° mm3 ris = 105.92 mm %3D t = 35.56 mm Sy = 1,933.67 x 10° mm3 %3D
600 150 150 Refer to the figure shown. Given are the following: Unit weight of concrete = 24 kN/m fe' = 35 MPa fse = 820 MPa fpu - 1,350 MPa Aps = 1,200 mm? foy = 1.080 MPa Beam is a simple span and have a length = 30 m. Determine the design moment capacity of the section. (kN-m) 00L
Please correct solution
Asap
AW14 x 43 column in a braced frame has a yield stress of 50 ksi and a height of 10 ft. The column is pinned at the top and bottom and has no intermediate bracing. Determine the available strength of the column considering the critical stress for flexural buckling. From AISC Manual Table 1-1, the properties of a W14 x 43 are: A = 12.6 in^2 tw = 0.305 in bf/2tf = 7.54 h/tw = 37.4 rx = 5.82 in ry = 1.89 in Ix = 428 in4 ly = 45.2 in4 G= 11,200 ksi J = 1.05 in^4 Cw=1950 in^6 What is the nominal axial strength considering flexural buckling stress of the column section (in kips). O 310 O 468 O 447 O 375 O 420 O 436 O 517 O 280
A cantilever beam having a 4m span carries a uniformly distributed load throughout its length. The beam is A36 steel with yield strength Fy = 248 MPa. The beam is not restrained against lateral buckling. The beam is W 21 by 62 steel shape, whose relevant properties are shown below: r = 0.053 m d = 0.533 m bf = 0.210 m tf = 0.016 m S = 0.002077 m3 Given this condition, solve for the allowable flexural stress in the compression flange. Use Cb = 1 as should be taken conservatively
Please answer asap with four decimal places
Example 2 (H.W) : For the simply supported beam of section shown in figure below, calculate the flexural stresses at ends and mid-span at all loading stages, then check these stresses with ACI limitations use fei' = 29 MPa, fe'= 35 MPa, Fpi= 1300 MPa, final losses =20 % live load= 5 kN/m, dead load =5 kN/m in addition to its own weight, span length= 13 m, class U and all live load is sustained. 600 mm 75 mm 700 mm I 50 mm 100 mm 100 mm
A compression member AB (HE 400 B) is pinned at both ends and braced in the weak direction as shown in the figure. Material and geometrical properties are given below. For the given loading and ASD load combination (PG+Pq=3500 KN), determine whether the section is satisfactory or not. Material: 5355 F355 MPa F 510 MPa E= 200000 MPa Section properties (HE 400 B): A: 19780 mm² d: 400 mm h: 298 mm t: 13.5 mm. tr: 24 mm b: 300 mm i,: 170.8 mm İy: 74 mm B X -BRACING IN THE WEAKDIRECTION
need asap auto like
A composite beam spans a distance of L= 12 ft and is fabricated by adhering two wooden boards (b= 2 in., d= 8 in. and E = 1,500 ksi) to the sides of a steel plate (t = 0.4 in., d = 8 in. and E= 30,000 ksi). 400 lb 400 Ib 200 lb/ft d -3 ft- 3 ft V (lb) -6ft 600 400 (ft) 12 -400 -600 1. For the given loading condition, determine the maximum normal stress M (lb-ft) in the steel plate. A) 3,850 psi +x (ft) B) 1,550 psi -300 C) 2,250 psi D) 4,200 psi -1200 - 1200 E) None of the Above 2. If the allowable normal stress of the steel is 9,000 psi and the 200 lb/ft distributed load remians constant, determine the largest acceptable concentrated load on each end. A) 1,600 lb B) 2,325 lb C) 935 lb D) 860 lb E) None of the Above
W X1 X2 L For the beam shown above with total length L = 10 m with a cantilever of length X2 = 3 m and a back-span length X1 = 7 m subjected to a uniformly distributed load of w = 2 kN/m, what is the magnitude of the maximum bending stress experienced by the beam if the cross section has the dimensions shown below: b = 75 mm d = 100 mm tf = 13 mm tw = 15 mm b tw * y_bar tf