W X1 X2 L For the beam shown above with total length L = 10 m with a cantilever of length X2 = 3 m and a back-span length X1 = 7 m subjected to a uniformly distributed load of w = 2 kN/m, what is the magnitude of the maximum bending stress experienced by the beam if the cross section has the dimensions shown below: b = 75 mm d = 100 mm tf = 13 mm tw = 15 mm b tw y_bar

W X1 X2 L For the beam shown above with total length L = 10 m with a cantilever of length X2 = 3 m and a back-span length X1 = 7 m subjected to a uniformly distributed load of w = 2 kN/m, what is the magnitude of the maximum bending stress experienced by the beam if the cross section has the dimensions shown below: b = 75 mm d = 100 mm tf = 13 mm tw = 15 mm b tw y_bar

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Text:A beam is made using the HE240A profile. The beam is 7 meters long and secured against displacement at node A and restrained against displacement in the vertical direction at node B, which indicated on the sketch. The beam is supported by a uniformly distributed load q= 6,40 kN/m between junction point A and B. and concentrated downward load P. Modulus of elasticity for steel is 2,0x105N/mm2. Cross-sectional data is obtained from steel table. A)Calculate how large the force can be when the transverse displacement (see image)apply superposition principle Calculate how large the transverse displacement (see image), , under the concentrated load will be for this the load effect. When the transverse displacement u(x) for a freely supported beam with uniform distributed load is: SEE IMAGE
Two uniformly distributed loads of w = 3600 lb/ftact on the simply supported beam shown in Figure A. The beam spans area = 6.8 ft and Z= 15.0 ft. The beam cross section shown in Figure B has dimensions ofb₁ = 15.00 in., d₁ = 5.00 in., b₂ = 11.50 in., and d₂ = 9.75in. Calculate the maximum tensile and compressive bending stresses produced in segment BC of the beam. W a FIGURE A FIGURE B tensile= compressive = d₁ d₂ B i i L b₁ b₂ W a psi psi X
The steel beam has the cross section shown. The beam length is L = 6.4 m, and the cross-sectional dimensions are d = 345 mm, by = 205 mm, t = 16 mm, and tw = 7 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if the allowable bending stress is 215 MPa. Answer: Wo Wo kN/m T₁₂ y
The steel beam has the cross section shown. The beam length is L = 7.1 m, and the cross-sectional dimensions are d = 385 mm, b = 190 mm, t = 16 mm, and tw = 8 mm. Calculate the largest intensity of distributed load wo that can be supported by this beam if the allowable bending stress is 250 MPa. Answer: Wo= WO kN/m
1. From the tabulation below determine if the column is safe to carry axial & bending load Yield stress of structural steel is 248 MPa. Modulus of elasticity is 200,000 MPa Service Load: Pl= Pd= assume K=1.0 Designation W8 x 28 W8 x 24 W8 x 21 W8 x 18 60 kN 100 KN Ag (mm2) 5323 4568 3974 2865 Weight/m d (depth) 42 bending moment Mux - Muy = 16 kN.m (LRFD load combination) bending moment Mx=My=12 kN.m (ASD load combination) L=3.6m flange Web 36 31 27 204.72 201.42 210.31 206.78 mm. width bf 165.99 164.97 133.86 133.35 thickness tf 11.81 10.16 10.16 8.38 thickness tw 7.24 6.22 6.35 5.84 Elastic Properties mm 4 mm 3 Ix x 106 Sxx 103 41 34 31 26 398 342 298 249 mm. rx 87.63 86.87 88.65 87.12 mm 4 lyx 106 9 8 4 3 mm 3 Sy x 106 109 92 61 50 mm ry 41.15 40.89 32 31.24 Plastic properties mm 3 Zx x 103 446 380 334 279 mm 3 Zy x 103 166 140 93 76 h=d-2k h 155.58 155.58 168.28 168.28
Answer as per attachment
2) An idealized free-body diagram of a door handle is shown below. To simplify, member X-Y is only experiencing torque while member X-Z is only experiencing flexure. What should be the minimum thickness of the handle of member X-Z if the maximum allowable flexure is 3MPa? What is the maximum torsional shearing stress experienced by member X-Y? What is the angle of twist? *G=83MPa. *When solving for torque, assume point Y as fixed support *When solving for flexure, assume point X as fixed support 200mm 100 mm 20 mm-dia. steel 11500N N
L For the beam shown above with length L = 7 m with the applied uniformly distributed load of w = 14 KN/m, what is the maximum bending stress if the beam has a cross section with the following dimensions: b = 100 mm d = 250 mm t = 20 mm tw = 15 mm tw
please step by step solution
The composite beam shown in the figure is simply supported and carries a total uniform load of 50 kN/m on a span of 4.0 m. The bearn is built of a wood member having cross sectional dimensions 150 mm x 250 mm and two steel plates of cross-sectional dimensions 150 mm x 50 mm. Determine the maximum stresses, in the steel and wood, respectively. If the moduli of elasticity are E {s} = 209GPA and E {w} = 11GPA (Disregard the weight of the beam) Steel 50 mm 50 kN/m Wood B Steel 50 mm 4.0 m- 150 mm 250 mm
For the beam shown above with total length L = 10 m with a cantilever of length X2 = 3 m and a back-span length X1 = 7 m subjected to a uniformly distributed load of w = 1 kN/m, what is the magnitude of the maximum bending stress experienced by the beam if the cross section has the dimensions shown below: b = 75 mm d = 100 mm tf = 13 mm tw = 13 mm