A simply supported beam shown in figure the beam is 7 m long, 197 mm wide and 591 mm deep with a uniform distributed load of 34 F N/m. Young's modulus of the material is 205 GPa. Calculate the slope at the ends and the deflection at the middle.

Q: Consider the beam arrangement with distributed load of 12 kN/m as shown in Figure 1. ii. Determine…

A: Given Data and Initial Calculation :- for ease of calculatation lets take 20kN instead of 12kN.

Q: A cantilever beam supports a concentrated load and a uniformly distributed load as shown in Figure…

A: Given

Q: A cantilever beam has a length L =12 ft anda rectangular cross section (b = 16 in., h = 24 in.).…

A: Calculate the moment of inertia of the beam. I=bh312 Here, I is the moment of inertia of the beam, b…

Q: Consider the simply supported beam shown below. Suppose that F=14 KN and w = 8kN/m. Take E=200GPa…

A: Step 1:Step 2:Step 3:Please rate the solution.

Q: The cross section of the wood beam is 4 in. by 8 in. Find the value of P for which the downward…

A:

Q: A cantilever beam shown below has a rectangular cross-section, 3/8 in. wide by 1 in. high. The…

A: Beam Details:Rectangular cross-sectionWidth (b) = 3/8 in.Height (h) = 1 in.Length (L) = 20…

Q: I need to find deflection of this beam. Some informationthat is not on the picture: length of the…

A: From the question, we have the following parameters:Length of the beam (L) = 215mmElastic modulus…

Q: A cantilever beam carries a partial uniform load w = 5 kN/m and a point load of P = 10 kN as shown…

A:

Q: 15 kip*ft 12 in 10 in 6 ft

A:

Q: Calculate the slope at C using ONE of these methods: double integration method, area-moment and…

A:

Q: Parvinbhai

A: The objective of the question is to determine the equation of the elastic curve of the beam using…

Q: 4. A rectangular shapped beam 150mm broad and 300mm deep by 3m long weighs 20kN. and E for the…

A: Given data: b=150 mmh=300 mmL=3 mW=20 kNE=190 GN/m2   It is required to determine the maximum…

Q: I need to find deflection of this beam. Some informationthat is not on the picture: length of the…

A: Step 1: Step 2: Step 3: Step 4:

Q: A cantilever beam of cross-section 90 mm. width 120 mm deep carries a UDL of 12 KN/m. over the…

A: When a cantilever beam having length 'L' is subjected to a UDL having intensity ω kN/m then maximum…

Q: Concrete: fe 30 MPa e - -0.002 Steel: fy- 400 MPa E,- 200,000 MPa A- 1500 mm 3-26M

A: Given data,pressure (fc1)=30 Mpa young modulous (εe1)=0.002fy=400Mpa shear pressure (ES)=200×103Mpa…

Q: A: 56m 47Nm Determine the maximum deflection and maximum slope of the simply supported beam of…

A:

Q: Find the slope deflections using any unit load method in the text book. For the beam shown in figure…

A:

Q: A cantiliver of length 20 m is subjected to a point load of 35 kN and a moment of 40 kN m at its…

A: Given data: The length of the cantilever beam is L = 20 m. The point load is F = 35 kN. The moment…

Q: Calculate the total load applied on the beam

A:

Q: Determine the x and y components of reaction at the pin A. Express your answers using three…

A: Given:F=50 kNFind:Part A: The x and y components of reaction at the pin APart B: The tension in cord…

Q: 12 kN/m 1 m- -1 m- E=200 GPa 1=4 x 10 mm Figure 1

A:

Q: A simply supported beam of length 6 m is subjected to a point load of 30 kN at its centre. The area…

A: Given data: Length of the beam, L = 6 m. The magnitude of point Load at the center of the beam, P =…

Q: L 25 mm dia. 5 kN

A: Given,  L = 4 in  d= 0.75 in  P= 499 lb

Q: Q1. A cantilever beam is carrying a UVL of 20000N starting at the free end and extends to 100000N to…

A:

Q: Find the section modulus for a beam of rectangular beam of breadth 45 mm, depth 50mm. The section…

A: We have to determine section modulus of beam

Q: I need to find deflection of this beam. Some informationthat is not on the picture: length of the…

A: First, we need to convert all the given units to base units for consistency. The length of the beam…

Q: I need to find deflection of this beam. Some informationthat is not on the picture: length of the…

A: From the question, we have the following parameters:Length of the beam (L) = 215mmElastic modulus…

Q: I need to find deflection of this beam. Some informationthat is not on the picture: length of the…

A: From the given information, it can be inferred that the beam is a simply supported beam with a point…

Q: The simple beam carries a concentrated load P = 20kN. Dimension a and b are 2.5m and 1.5m.…

A:

Q: A simply supported beam of dimension 4m x 45mm x 90mm, which is subjected to a mid-point load of 130…

A:

Q: antilever beam has flexural rigidity is EI=200 × 106 N.m2 is loaded with a concentrated force at its…

A: Given:EI=200 × 106 N.m2Area of bending moment diagram =10000 N.m2Find,Slope at free end?

Q: A cantilever beam shown carries a concentrated load of 20 kN at point C. Assume constant value of E.…

A: Draw the free body diagram of the beam and find the reactions. The reaction force at A will be…

Q: A 19 ft long, simply supported beam is subjected to a 5 kip/ft uniform distributed load over its…

A: Here, Length of the beam = L = 19 ft = 228 in Uniform loading = w = 5 kip/ft = 0.4167 kip/in = 416.7…

Q: Figure Q1 (a) shows the beam is subjected to a moment of 100 kN.m. (i) Compute the centroid and…

A:

Q: a 50mm x 200mm beam is supported has a 2kN load placed 1m from the left reaction. calculate the…

A: Detailed solution is given below, still if you have any query please feel free to contact me.Thanks…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.