A simply supported beam of length L is load with a moving concentrated load P passing across the span of the beam. Determine the maximum shear force that will carried by the beam. a) P b) P/2 c) P/4 d) 0

A simply supported beam of length L is load with a moving concentrated load P passing across the span of the beam. Determine the maximum shear force that will carried by the beam. a) P b) P/2 c) P/4 d) 0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

F1 Determine the reaction forces for girder G-1. Column A Beam B-1 L1 -0 Beam B-2 F2 Girder G-1 Please round to the nearest one. Reaction force for Girder G-1 (Column A side) = Girder G-2 L1 After the initial calculation, we determined the following information: • The reaction force for Beam B-2 (Girder G-1 side) = 17,890 lbs • The reaction force for Beam B-3 (Girder G-1 side) = 15,685 lbs Reaction force for Girder G-1 (Column B side) = 80 F3 • Live load 50 psf • Dead load: (1) Slab = 50 psf, (2) Deck = 10 psf, (3) Mechanical equipment = 8 psf, (4) Suspended ceiling = 8 psf (5) Beam = 25 lb/ft, (6) Girder = 35 lb/ft • Beam and Girder spacing:: (1) L1 = 14 ft, (2) L2 = 10 ft, (3) L3 = 10 ft Beam B-3 000 000 F4 lbs open lbs F5 L1 Column B Beam B-4 L2 F6 L3 MacBook Air ← F7 F8
Based on the following figure determine the vertical reaction at the hinge type support for the loads shown on the beam. Consider that the dimensions are in meters. For the exercise use a value of x equal to 7.3 m, a value for the distributed load w equal to 160 N/m and a value for the force F equal to 532 N.
HELP MEEEE
A beam is made up of two identical bars AB and BC, by hinging them together at B. The end A is built-in (cantilevered) and the end C is simply- supported. With the load P acting as shown, the bending moment at A is 14 L B O L/2 P 4 L
The beam is subjected to a uniform live load of1.2 kN/mkN/m, a dead load of 0.5 kN/mkN/m, and a single live load of 45 kNkN. Assume AA and CC are roller, and BB is a short link. Follow the sign convention. The distributed live load can be applied to several segments of the beam that are not necessarily adjacent. (Figure 1) A)The beam is subjected to a uniform live load of1.2 kN/mkN/m, a dead load of 0.5 kN/mkN/m, and a single live load of 45 kNkN. Assume AA and CC are roller, and BB is a short link. Follow the sign convention. The distributed live load can be applied to several segments of the beam that are not necessarily adjacent. (Figure 1) B)Determine the maximum positive shear at EE. y D B E 4 m 4 m 4 m 4 m
I need answer within 20 minutes please please with my best wishes
What is the maximum absolute shear for the following beam and load group? Use L = 21, a = 3, b = 4, P1 = 2, P2 = 4, and P3 = 4. ܢܢܢܢܢܢܢ L P₁ P2 미미 a b P3
Properties 1. compute the web shear capacity a. compute the horizontal shear copacity (kN) a the JIS00 mm2 arca depth width oF Flange thickness Df Flange 350 mm Dettral axis 2I0 mm 16 mm 3. 1F the Girder was used as an 8meter long simple span capries equal concentrated dead load,P at evay quarter points and determine the load P based on shear copacity. 10 mm web thickness uniform load of 12. a KN/m, a wwgo1x クりの 45Xr0 mm? Fy 248 M Pa 4. calcubte the maximum shear it used as a 'F Fb 148 MPa 8m beam simply supportcd at the lept end and 2meter prom the right end which carries a total unitorm FV 99 MPa cocad of 45 kN/m.
Determine the force in each member of the pin-connected truss. AE is constant. Use force method
Question (1): A rectangular beam has a width b = 400 mm, and effective depth d= 850 mm and a total height h = 900 mm. The beam is subjected to an ultimate moment M, = 1500 kN.m and an ultimate shear force Vy = 700 kN. 1-) Design the beam for flexure to calculate the required area of steel. 2-) Using stirrups o 10 mm (No.10) diameter, calculate therequired spacing (s) between the stirrups at the ultimate shear force section.