A simply supported beam of length 2L is subjected to a uniformly distributed load 2w per unit length over its entire span. Additionally, a ring support located at the mid-span (L/2) applies an upward force to the beam. The magnitude of this force is one-third of the total load acting on the beam. Given the beam's material properties and dimensions, the goal is to determine the spring constant (k) of the ring support. 2w per unit length eee

A simply supported beam of length 2L is subjected to a uniformly distributed load 2w per unit length over its entire span. Additionally, a ring support located at the mid-span (L/2) applies an upward force to the beam. The magnitude of this force is one-third of the total load acting on the beam. Given the beam's material properties and dimensions, the goal is to determine the spring constant (k) of the ring support. 2w per unit length eee

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the figure shown, the rigid beam with negligible mass was horizontal before the load P was applied. Determine the value of load P if the vertical movement at P is 3mm. Draw the FBD and deformation diagram.
A two-storey apartment building designed by Engr. Sang Woo has a brace system of main structural member shown in the figure. Considering that the bars are stressed - free the time it was assembled at 25°C. Determine the normal stresses in MPA of rods given that: Bronze (1) Aluminum (2) E= 100 GPa E= 70 GPa a = 16.8 x10 6 / °C Ø = 21mm a = 22.8 x10 6/°C Ø = 15 mm Note: After assembly it has been observed that the bronze rod 350 mm 250 mm (1) temperature remains the same while aluminum rod decreased by 42°C. Round off your answers to nearest whole number 200 mm (2) 500 mm
A steel specimen of 12 mm diameter extends by 6.31 x 10-2 mm over a gauge length of 150 mm when subjected to an axial load of 10 kN. The same specimen undergoes a twist of 0.5° an a length of 150 mm over a twisting moment of 10 N-m. Using the above data, determine the elastic constants E, Mu, G and K.
!!!
Please provide the answer in three significant figures
Bar A has diameter 'd' and bar B has diameter '2d'. Both are of the same length and are of the same material. If they are subjected to same axial load P, the ratio of extension of bar A to B is (B) 2 (A) 4 (C) 0.5 (D) 0.25
Building material H.W1
As a construction engineer, you are asked to evaluate the maximum allowable vertical shear Vmax that may act on the hollow stainless-steel beam having a rectangular cross section as shown in Figure Q4. Discuss the effect of geometry on the shear stress developed in the beam | 20 mm y 350 mm V 10 mm- -10 mm 1 30 mm E 200 mm
SHOW COMPLETE SOLUTION AND ILLUSTRATION
A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi; α = 2.9 × 10-6/°F] bar (1) and an aluminum alloy [E = 10,000 ksi; α = 12.5 × 10-6/°F] bar (2), as shown. Each bar has a cross-sectional area of 2.00 in.2. The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 56 kips is applied and the temperature is increased to 100°F, determine the normal force in bar (1).
A load P will be supported by a structure consisting of a rigid bar ABCD, a polymer [E = 2,300 ksi; a = 2.9 × 10-6/°F] bar (1) and an aluminum alloy [E = 10,000 ksi; a = 12.5 × 10-6/°F] bar (2), as shown. Each bar has a cross-sectional area of 2.00 in.². The bars are unstressed when the structure is assembled at 30°F. After a concentrated load of P = 69 kips is applied and the temperature is increased to 100°F, determine the normal force in bar (1). 6 ft 2.5 ft 07.01 kips 5.63 kips 8.39 kips 9.29 kips 6.66 kips (1) B 3 ft C 8 ft 1.5 ft