A simply supported beam is subjected to a uniform service dead load of 1.0 kip/ft (beam weight is to be included), a uniform service live load of 3 kips/ft, and a concentrated service live load of P. The beam is 30 ft long, and the concentrated load P is located at the mid-span. The beam has continuous lateral support and W27x84 A992 steel is used. What is the maximum permissible value of P in kips for LRFD? Express your answer in three decimal places.

A simply supported beam is subjected to a uniform service dead load of 1.0 kip/ft (beam weight is to be included), a uniform service live load of 3 kips/ft, and a concentrated service live load of P. The beam is 30 ft long, and the concentrated load P is located at the mid-span. The beam has continuous lateral support and W27x84 A992 steel is used. What is the maximum permissible value of P in kips for LRFD? Express your answer in three decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An A36 W14X605 simply supported steel beam with span “L” carries a concentrated service liveload “PLL” at midspan. The beam is laterally supported at supports and its midspan. Consider its beam selfweight to be its service deadload, “w” (use ASEP steel manual for selfweight, w and other section properties). a. Check for compactness of the given section? b. In checking section's compactness, calculate the upper limit for compact flange category? c. In checking section's compactness, calculate the upper limit for non-compact web category?
RCDA reinforced concrete T- beam, section in Figure 2 (a), is subjected to an ultimate uniformload and concentrated loads as shown in the Figure 2(b). The beam is reinforced with 6-28 mm diameter tension bars at the point of maximum positive moment (at midspan -bars at the bottom), and 3-28 mm diameter tension bars at the point of maximum negativemoment (at the supports - bars at the top) .. The design properties used are: f ‘c = 21MPa and fy = 414 MPa, ; flange width = 650 mm, flange thickness is = 90 mm; webthickness = 250 mm; effective depth = 410 mm.Need to answerQ. Draw the shear and moment diagrams for the given loads;
Please correct solution
AW14 x 43 column in a braced frame has a yield stress of 50 ksi and a height of 10 ft. The column is pinned at the top and bottom and has no intermediate bracing. Determine the available strength of the column considering the critical stress for flexural buckling. From AISC Manual Table 1-1, the properties of a W14 x 43 are: A = 12.6 in^2 tw = 0.305 in bf/2tf = 7.54 h/tw = 37.4 rx = 5.82 in ry = 1.89 in Ix = 428 in4 ly = 45.2 in4 G= 11,200 ksi J = 1.05 in^4 Cw=1950 in^6 What is the nominal axial strength considering flexural buckling stress of the column section (in kips). O 310 O 468 O 447 O 375 O 420 O 436 O 517 O 280
2. Determine the lightest W-shape for a column 30' tall in a braced frame. The column is braced at mid-height in the weak direction. The loads are 100k dead load and 200k live load. The bottom of the column is pinned and the top of the column is constrained in rotation.* Use A572 Grade 60 steel. *Not tronslation.
i need the answer quickly
A reinforced concrete simply supported beam has a span of 20 ft and supports service dead load of 2.5 kip/ft and a uniform service live load of 2.5 kip/ft in addition to its self-weight. Design a beam section as per ACI 318-14 to resist the factored external bending moment. The concrete compressive strength at 28 days is(4 + 15)ksi and yielding strength of steel is (60+ 15)ksi.
Solve it
Topic: BEAM BEARING PLATES AND COLUMN BASE PLATES - STEEL DESIGN
A reinforced concrete cantilever beam is shown below. The beam cross section is a rectangle, 12 inches deep by 18 inches wide. Material properties are: - Concrete weight: wt = 150 pcf - Concrete compressive strength: f'c = 4000 psi - Concrete tensile strength: f't = 400 psi - Steel tensile strength: fy = 60 ksi - Stirrup consists of #4 bar - Beam is not exposed to weather or in contact with soil. Determine if the beam will crack under its own weight, if its self-weight is 250lb/ft. 10 ft -18" BEAM SECTION beam will crack beam will not crack unknown, not enough information to calculate
The answer is between 18.25 and 20.25
A compression member AB (HE 400 B) is pinned at both ends and braced in the weak direction as shown in the figure. Material and geometrical properties are given below. For the given loading and ASD load combination (PG+Pq=3500 KN), determine whether the section is satisfactory or not. Material: 5355 F355 MPa F 510 MPa E= 200000 MPa Section properties (HE 400 B): A: 19780 mm² d: 400 mm h: 298 mm t: 13.5 mm. tr: 24 mm b: 300 mm i,: 170.8 mm İy: 74 mm B X -BRACING IN THE WEAKDIRECTION