A simply supported beam is shown in the figure. El = 56,000 kN-m2. Using Double tion Method determine the following: A. Determine the slope at point B. Express your answer in degrees. B. Determine the deflection at point C. Express your answer in millimeters. c. Determine the maximum deflection of the beam. Express your answer in millimeters.

A simply supported beam is shown in the figure. El = 56,000 kN-m2. Using Double tion Method determine the following: A. Determine the slope at point B. Express your answer in degrees. B. Determine the deflection at point C. Express your answer in millimeters. c. Determine the maximum deflection of the beam. Express your answer in millimeters.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

determine the beam deflection at point H. Enter your answer in mm to 2 decimal places.
The bending moment diagram and cross-section for a beam are shown below. Use the elastic flexural formula ox = -Mzy/l, to determine the required strength of the beam to resist the compressive stresses. Circle the correct answer for the compressive strength in ksi: 2.3, 2.5, 27.5, 30, 37.7 Show your work below. Bending Moment Diagram Beam Cross-Section 4" +50 2' (K-Fe) 2" 2" - 40 2"
Perform double integration of the bending moment equations. You will obtain deflections in this form (can be found in the image attached) Calculate: the value of the constant integration C2. Enter your answer in kNm2 to three decimal places. b) the value of the integration constant C4. Enter your answer in kNm2 to three decimal places. c) the value of the deflection at point C. Enter your answer in mm to three decimal places.
QUESTION 3 If the allowable bending stresses for a beam in one application is 6 kip/in2 in tension. The cross-section of the beam is W8 x 40. If the beam is 10 foot long and simply supported and has a concentrated load applied at x = 3 ft as shown below. • Generate the shear force and bending moment diagram in terms of P; • Based on the allowable maximum bending moment you just obtained above, calculate/ input the mazimm allowable value of the load P: please, pay attention to units, and calculate your answer to 1 decimal place.. 3 ft 7 ft kip.
In (Figure 1), w = 3.8 kip/ft and F=20 lb. Follow the sign convention. Part A Determine the shear force acting at point D of the beam. Express your answer in kilopounds to three significant figures. vec VD = kip Figure 1 of 1 Submit Request Answer Part B Determine the moment acting at point D of the beam. Express your answer in kilopound-feet to three significant figures. A, 6 ft 9 ft ΑΣφ vec MD = kip ft %3D
Q/ For the beams and loading shown below. A-Draw the shear force and bending-moment diagrams. B- Determine the equations of the shear force and bending-moment curves for the segments CD in Figure 2 C- Compute the bending stress at point (a) on section C. D- Determine the values and locations of the maximum tensile and compression bending stresses. Figure (2) R Point a Radius of hole: 40kN 0.5m 30 20KN/m 0.7m A B D |B 1m Im 3m Radius = R= 100 mm
Question 2 Determine the maximum deflection of the beam and the slope at A. Use Macaulay's brackets in your derivation, setting the origin at A, to find a single expression for the slope and deflection over the entire length of the beam. El is constant. Mo Mo
Problem 2 (30 points): The formula for the deflection of the beam shown is: Wo y(x) = (-x5 + 5Lx-10L?x3 + 10L³x²) 120LEI Wo 15 x 107 N L = 2m %3D max m E = 7 × 1011 N m2 I = 6 x 10-4m Use the Newton-Raphson Method to determine the x location along the beam where the deflection is y(x) = 0.14 m. Use a starting guess of xo 1.2 m. Be sure to show your %3D calculation for the derivative of the function and your calculations you use to fill out the table. You only need to perform two iterations of the method, which means you should fill out the table below. Notice that y is defined as positive in the downward direction, which means that both the function and the target deflection are positive values in the coordinate system. y(xn) y'(xn) Xn+1 Step Xn 2.
Using a computer and step functions, calculate the shear and bending moment for the beam if P-16 kN. Use the specified increment AL. starting at point A and ending at the right-hand support. (Round the final answers to two decimal places) ها 1.2 m 16 kN/m AL-0.4m The maximum shear stress is The maximum bending moment is KN. kN m.
The cross-section is shown to the right of the beam. For the cast iron beam what is the maximum deflection in the beam? Note: Young’s modulus is 172 GPa.
Problem 2 Moment-Area Method: For the given beam below, answer the questions. El = constant: 5 kN 8 kN-m A В 6 m 6 m 6 m (b) (c) | Draw the Curvature Diagram of the beam. Mark all important values. Determine the slope at point A, 64, using the moment-area method. | Determine the deflection at point B, Ag, using the moment-area method.
Consider the T-beam shown in (Figure 1). Suppose that aaa = 80 mmmm , bbb = 160 mmmm , ccc = 10 mmmm . 1. Determine y¯y¯, which locates the centroidal axis x′x′ for the cross-sectional area of the T-beam. 2. Determine the moment of inertia Ix′Ix′. 3. Determine the moment of inertia Iy′Iy′.