The 2 X 12 joist shown in Figure has an Ixx value of 178 in.“. What will be the percentage decrease in this value if a hole 2 in. in diameter is drilled through it at location A? 1.5 2 11.25

Q: a) An alumium shaft shown in figure-2, has x-sectional area in the shape of equilateral triangle. if…

A: given data: for equilateral triangle : τallow=56MPa    ,φallow=0.02rad   Gallow=26GPa=26*103MPa side…

Q: A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2 = 1.0…

A: Solution;   Note: The stress concentration factor kt values are taken from the stress concentration…

Q: Instructions: Draw the shear and bending moment diagram of each beam loaded as shown. Show your…

A:

Q: Decimal Places Only 13. For the beam loaded as shown in figure 5, determine the following unknown…

A: The degree to which a structural member can be shifted by a significant amount of load is known as…

Q: * For the cross section shown in the figure. :Find the value of Y 40 mm A1 250 mm

A: Given

Q: b) Find the length CF, length GF, angle 01 and 02 for the diagram below. 5 kN

A: Consider the diagram shown below for the given truss.

Q: Calculate the moment of inertia of the shaded figure about its base a-a.

A:

Q: Find the moment of inertia (in mm4) of the shaded area with respect to the yaxis. Round off only on…

A:

Q: a) Determine the second moment of area (IXX) about the centroidal x-axis for the solid homogeneous…

A:

Q: situation; a) Maximum normal stress

A:

Q: If the sections shown below is subjected to a negative bending moment of 10kN.m, draw the 3D bending…

A: As Given Data From the question y=87.65mm                      *****Distance from neutral axis***…

Q: PART 1: ANALYSIS OF BEAMS QUESTION 1. Given the simple beam ABC, determine the reaction at the hinge…

A:

Q: If a 12-ft long portion of the bar in Question 23 is elongated 0.064 in. by the pull, the unit…

A:

Q: Determine the moments of inertia for the cross-sectional area of the member shown in the Figure…

A: Moment of inertia of an area is defined as the product of area and the distances of its center from…

Q: In the Figure 5, the new length of the cantilever beam due to the inclined force (P) is (in mm):…

A:

Q: se Mohr's circle to find the stress on the slope indicated by the dotted line when the stress state…

A:

Q: (c) Determine the 1st moment of area Q, of the top-half region A' (red shaded area) against z axis,…

A:

Q: c. The cross-section of the beam is shown in Figure 2.2. Calculate the vertical position of the…

A:

Q: solve for the direction and put a conclusion after getting the answer. Make sure that the answers

A: Resultant load is equal to the area under the curve Resultant load pass through CG of load

Q: Locate the centroid ( ¤, y) of the shaded area.

A:

Q: 15 mm 100 mm 50 mm 50 mm 1₂ 100 mm Part A 60 mm 15 mm 60 mm Determine the moment of inertia of the…

A:

Q: Consider the beam in (Figure 1) with a = 13 in. igura Determine the product of inertia of the beam's…

A: Given data is

Q: 2. What is the moment of Inertia of the following cross section. Please give the moment of inertia…

A: Given

Q: Determine the vertical displacement, in mm, of point C of the beam shown in the figure below. The…

A:

Q: The beam cross-section shown in the Figure Q6 is subjected to a resultant internal vertical shear…

A:

Q: 1a) 1,-금eor 1 + 2| 0.11* + 2 0.11+ 0.9244? = 3.07,* 6. r d 4r 0.9244r y . Зл 1 I, • · (2r)' +- r*…

A:

Q: The figure shows cross-section of a beam subjected to bending. The are moment of inertia (in mm4) of…

A:

Q: k P 0 8 ft x = 11.1 ft x RA 8. W (ft) Calculate the magnitude of the bending moment at distance x as…

A:

Q: A B Cell 1 Cell 2 с D Figure 1. A double-cell thin-walled section of a fuselage. Table 1. Geometric…

A:

Q: Write the-Point-Slope equation-for the line through. the point- P.withSlopem-- --P(リナm= P--P(-4,0) -…

A: Given Data (a)  Given point is :P1,1 Given slope is: m=1 Therefore from the point slope equation…

Q: Find the allowance.

A: Shaft:

Q: what is the total length required of an aluminum sheet metal to form a 11 by 11 square shown in the…

A: First of all, calculate the length of aluminium sheet which is not in contact with rebar.…

Q: Draw the diagrams for all the sections views, using the dotted outlines as a guide. Assume that the…

A: Draw the diagrams for all the sections views, using the dotted outlines as a guide.

Q: ajor principal axis of the section with respect to

A: major principal axis can be obtained as below,

Q: Determine the vertical displacement of joint C . EA is constant

A: The vertical displacement of the joint C. FBD: The free-body diagram of the joint C is shown below.

Q: Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown below if P…

A: The bending stress at the top of the beam at point C: ( 63.2527 × 106 ) Pa ... (Compressive)

Q: Question # 4. For the shaded area shown in the figure: 100 mm a) Calculate the moment of inertia…

A: y =x2/50 x =50y IX' = ∫y2dA take a small area element dA at a distance y from x-axis dA =2xdy  dA…

Q: The rim of an iron flywheel's cross section (S+3) ft. A 12" by 3" triangle has a diameter of 12".…

A:

Q: In order to bore the tapered hole a straight hole must be drilled or bored. Find the size of the…

A:

Q: y - y² = 1 – 0.5x | 1 m 1 m - 2 m- Figure Q10 a) the moment of inertia of the shaded area about the…

A:

Q: Draw the shear and bending-moment diagrams for the beam and loading shown, and determine the maximum…

A: Support reaction calculations:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.