A simply supported beam is 15 ft in length. It carries a uniformly distributed load including its own weight of 80 lb/ft and a concentrated load of 500 lb, 6 ft from the lright end. Determine the reactions at the support and the position of the resultant load from the left support. Pls show full solution with figures.

Q: Determine the maximum shear and moment for the beam shown below.

A:

Q: Determine the shear force 5.67 ft to the right of point A for the beam shown belowif P = 843 lb, W =…

A:

Q: The following beam has a self weight (dead load) of 150 lb/ft and is subjected to a uniform live…

A:

Q: For the beam shown bel ow: a) Draw the shear force and bending moment diagrams; P A В D Hinge a b…

A:

Q: A beam is used to support a concentrated load of 12 kN and a distributed load (w). The beam has the…

A: ∑MB=0 -12 x 3 - RC x 9 = 0 RC = -4 kN ↓ ∑V=0 RA + RC = 6 x 9 - 12 RA = 46 kN ↑ ∑MA=0 -MA + 6 x 9 x…

Q: A typical rigid bar AB of the length 5m for a cantilever type car shed as shown in figure is hinged…

A: The given data is as follows: Length of bar AB=5 mDiameter of steel wires=3 cmDistance of wires from…

Q: Consider bending contributions only and take that the flexural stiffness as EI. Problem 1: Find the…

A:

Q: Dr. Luma Fadhil hanics of Materials 2nd Class Sec.: F Draw the shear-force and bending-moment…

A:

Q: A beam at right carries a uniform load w across its full length. Use this beam to respond to…

A:

Q: Read the question carefully and give me right solution according to the question. The two span beam…

A:

Q: Determine the shear force 5.67 ft to the right of point A for the beam shown belowif P = 843 lb, W =…

A:

Q: a) Draw the shear force diagram (SFD) and bending moment diagram (BMD) for the beam shown in Figure…

A: In the above beam structure we need to calculate the reaction initially, the reaction  calculate by…

Q: Pi P: Х D E 3.8 L FIGURE Q1(a)

A: For any beam or structure load acts at any point or distributed load then due to that bending and…

Q: If it is known that the column is part of the unswayed frame structure and has a single curvature…

A: To check whether the reinforced concrete column is capable of carrying the ultimate factored load,…

Q: 6 klft 24 k-ft 7 K8' →K5'5' → T CHOOSE THE OPTIMAL TO SUPPORT THE LOADS. A WIDE FLANGE BEAM

A: Given simply supported beam with loading conditions and it is asked to choose the optimal wide…

Q: Determine the Reactions of each beam. Show the Distributed Load Resultant magnitude and location on…

A:

Q: 4. Compute the safe concentrated load P that the beam could carry at a distance of 1 m from the…

A:

Q: A two-span continuous T beam is supported on three concrete walls spaced 20ft on center. The beam is…

A: Beam dimensions: 12" x 36" with a flange that is 4" deep and 40" wide.Spacing between concrete…

Q: 2) 10 kN 10 kN 5 kN/m В D G |lm 3 m H 3 m 4 m

A: Answer:-                 In this question we will use the concept of hinge and equation of…

Q: If the allowable bearing stress for the material under the supports at A and B is Ob = 730 psi,…

A:

Q: Q2: A simply supported beam AB has a length of 3 m and carries distributed load which varies in…

A: Draw the free body diagram. Equilibrium of horizontal forces, ∑Fx=0Ax=0

Q: For the beam and loading shown, determine the vertical reaction at A (Ib) provided that a=180,…

A: Ay=551.67lb (upward) By=163.33lb (upward)

Q: Completely solve and box the final answer. Illustrate the problem. Write legibly 3. A 250 mm by 350…

A: Given Data:b=250mmd=350mmL=8mLoads =90kN, 75kN and 60kN  Required-To  determine the maximum bending…

Q: A simply supported steel joist with a 4.0 m effective span carries a uniformly distributed load of…

A:

Q: Completely solve and box the final answer. Illustrate the problem. Write legibly 4. Compute the…

A: Given Data:Span of beam=L=4mCross section of beam=50×200Shearing stress = 0.70 MpaIt is asked to…

Q: M1 at point B is 10 kips-ft, P1=12 kips is 9 ft from point A; and w1 = 1.5  kips/ft is distributed…

A: Solution: Convert the udl into singular concentrated load: P2=load x length =1.5 ×22P2=33 kN The…

Q: A heavy storage warehouse building is made of 200 mm thick stone concrete floor. The floor slab…

A: Free Body Diagram I=bd312I=250*300312I=5625*105mm4E=200kN/mm2EI=112500kNm2∑Fy=0---(Upward positive…

Q: A simply-supported beam carries a uniform load, w = 123 kN/m at its middle third. If L = 14 m,…

A: Determine the absolute value of the maximum bending moment???

Q: 9 ft 13 ft 22. Inad Nianram M1 at point B is 10 kips-ft, P1=12 kips is 9 ft from point A; and W = 1.…

A: P1=12kips W1=1.5kips/ft To find resultant force and it's location from point A

Q: ne cross sectic tional area of nolumn CE

A: for equilibrium   H + 2H+ = 3 ∑MG = 06×H - V ×10 =06×H10 = V  V = 0.45 Kips  v = 0.45 kips   H =…

Q: Determine the maximum uniformly distributed load that can be loaded for the beam shown if the…

A: σt = 88MPa σc = 128MPa

Q: A 40 mm. diameter bar is used as a simply supported beam 2 m long. Determine the largest uniformly…

A:

Q: A concrete beam has a cross sectional area of 275mm width and 150mm height for the upper flange.…

A:

Q: Determine the nominal moment of the rectangular beam shown in the figure (3-2). Where fe' = 37 Mpa,…

A:

Q: Determine the following: a. Maximum negative shear at B b. Maximum positive shear at B c. Maximum…

A:

Equilibrium and Support Reactions

Civil engineers deal with structures that are composed of several members connected or with individual members such as beams and columns. To analyze such structures, the condition of statics must be applied. Under the static condition, the members are considered to be in equilibrium under the action of forces, that is, the members are assumed to be having negligible velocity.