A-Simplify the block diagram shown in Fig.2a and obtain the transfer function C(s)/R(s). 2013 H,(s) G(s) G(s) G,(s) C(s) H,(s) G,(s) SAP PROC INVOIC ATER JOSIE CONTRERAS

Q: difference between measurement uncertanty and measurement error

A: Given : Need to find the difference between measurement error and uncertainty.

Q: it is called as the difference between the value and the measured value of a quantity a. mistakes b.…

A: In this value we will find significant figures...

Q: Is Mc microfarads?

A: Given, The abbreviation of mc =?

Q: In an electronic circuit, a. current remains the same through all the series components. b. voltage…

A: Note that,  In an electronic circuit, current remains same jn all series components and voltage…

Q: Choose which answers are correct ‎‏What is the unit of slope of a Fuel cost curve ? a . $ / MWh b .…

A:

Q: Sl.no Symbols Name of the components 1. 2. 3. 4.

A: here, the various symbols of the pneumatic circuits are given  which can be useful to make PLC…

Q: What is sub station

A: A power station is to provide electricity to a huge number of people. Different customer’s power…

Q: What information is contained in the specification K, 10,000

A: Kp stands for the position error constant for the step input function.  here, Kp = 10000

Q: recall the topcis of the electronic Device and circuits

A: There are many topics in EDC  These topics are  1- Semiconductor diode  2-Diode circuit

Q: In static characteristics, is defined as the difference between the true value applied to a…

A: in static characteristics, Accuracy is defined as the difference between the true value applied to a…

Q: In a rectifier circuit , DC output voltage and RMS output voltage is  0.3 V & 0.6 V respectively.…

A:

Q: What is HT supply?

A: What is HT supply?

Q: Difference in the digital and the analog systems

A: Both digital and the analog systems are used to transmit and received information (or signals). The…

Q: IEEE and IEC standards

A: standards for electrical safetyIEC - international electrotechnical commissionIEEE - institute of…

Q: Q2: (A)Find the following: 1- (110)10+ (0111)2.by using BCD numbers. 3-(3E91)16- (1F93)16by using…

A: The number system is used to represent information in digital electronics. Different bases exist in…

Q: tronic components definitions and si units and color coding

A: Electronic components : There are mainly two type of Electronic components one is active Electronic…

Q: Label the parts of Tubular Steel Poles

A: Steel tabular poles are not commonly used poles these poles are used when there is need of low cost…

Q: A transistor is used as a switch and the waveforms are shown below. The parameters are given as…

A: Given  Transistor as switch and waveforms as shown  Vcc=200 vVCE(sat)=1 vICS=100 AICEO=1 mArise time…

Q: Use electricity cost $0.08 to $0.30 in increments of $0.01. Compute a column for each type of bulb…

A:

Q: Define Analog

A: Analog can be defined as the signal, which is continuous. The analog signal has a time-varying…

Q: Please show the work in between the rearranged formula and the answer

A: Given: Calculate the S/N in dB if the passband circuit is 48kHz to 64kHz and the maximum bit rate is…

Q: Experiment Title SIGNAL GENERATORS

A: WE have to discuss signal generator, The sine wave generator represents the largest single category…

Q: The neutral current is equal to three times of ....... sequence current.

A: Current in nautral is sum of three phase currents. Current in each phase is sum of possitive…

Q: From the table, what is the circular mils for the following: a. 14 AWG a. 10 AWG b. 30 AWG c. 20 AWG

A:

Q: 19. Identify the response time of a meter. a. Time taken by output to reach final constant value…

A: Identify the response time of a meter. It's depend on the parameter.

Q: Discuss the operation of a multi-meter

A: Solution :    In the above question they are interested to know the operation of a multimeter.   As…

Q: Determine Reg in Ohms at the (a,b) terminals for the following circuit. Round your answer to the…

A:

Q: HERE IS IT

A: Physical address can be expressed by the following formula:Physical Address = (Segment Address) x 10…

Q: Use block diagram formula

A:

Q: 3) What is the dropout ratio? What is the advantages of dropout ratio in power systems. (min 1 page)

A: A pick-up and drop-out ratio terms related to protective relays. The pickup current of a circuit…

Q: An offset / must be introduced into a metal tube of 0.75-in. outer diameter and 0.08-in. wall…

A: An offset h must be introduce into a metal tube of 0.75-in.outer diameter and 0.08-in.The internal…

Q: Explain the Difference between the Fundamental and Derived Unit.

A: There are generally  three types of units which are used to typically measure a particular physical…

Q: Hi for case 3 is explain on which question ? either (a) positive or negative or for question (b) pls…

A:

Q: Give the title proposal about renewable energy atleast 5 title Bachelor electrical engineering

A: Renewable Energy:- Renewable energy is produced using resources found in nature that are not…

Q: Identify the elements considered for the Voltage Drop calculations in D.C distribution system. О а.…

A: For DC distribution, voltage drop across the element?

Q: What is the UPS

A: A uninterruptible force supply (UPS) is a gadget that permits a PC to continue to run for in any…

Q: Give the concise definition or process of getting the equations in each loop/mess (Mesh Analysis) in…

A: Let us try to understand the concept of mesh analysis in this answer.

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.