as ap (a) A simplified block diagram of pressure vessel for hydrogen is shown in Figure Q4 (a).By using root locus approach, investigate either each of these statement is correct orincorrect to represent the root locus characteristics for the system.Q4(i) Number of locus that end at infinity is 2.(ii) The asymptote of the infinite zeros is at 1.5.(iii) The angles of the lines that intersect at 1.5 are 90° and 270°(iv) The jo-axis crossing are at j±1.82.(v) Angle of departure is at -31°.R(s)KC(s)s(s² +2s +2)2s +10

Answered: Image /qna-images/answer/f8b987f9-7b09-46f3-bb82-320ce533a107.jpg

A simplified block diagram of pressure vessel for hydrogen is shown in Figure Q4 (a). By using root locus approach, investigate either each of these statement is correct or incorrect to represent the root locus characteristics for the system. Q4 (а) (i) Number of locus that end at infinity is 2. (ii) The asymptote of the infinite zeros is at 1.5. (iii) The angles of the lines that intersect at 1.5 are 90° and 270° (iv) The jo-axis crossing are at jt1.82. (v) Angle of departure is at -31°. R(s) K C(s) s(s² +2s + 2) 2s +10

A simplified block diagram of pressure vessel for hydrogen is shown in Figure Q4 (a). By using root locus approach, investigate either each of these statement is correct or incorrect to represent the root locus characteristics for the system. Q4 (а) (i) Number of locus that end at infinity is 2. (ii) The asymptote of the infinite zeros is at 1.5. (iii) The angles of the lines that intersect at 1.5 are 90° and 270° (iv) The jo-axis crossing are at jt1.82. (v) Angle of departure is at -31°. R(s) K C(s) s(s² +2s + 2) 2s +10

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

You work as a material engineer at an aircraft development, manufacturing and maintenance company in the MENA region. Recently, the manufactured airplanes have been experiencing crashes after a couple of years in service. You have been assigned as a member in the investigation team to identify the main cause of the crashes. a) Discuss which hysteresis is better to be used with the AC generator in the airplane. b) In general, describe the structural, elasticity and electrical properties of copper and the PVC insulator (polymeric) with reference to their material properties. c) How metals and non-metals (ceramics and polymers) could be degraded?
power system please answer as soon as possible
Q5. Predictive maintenance is to be applied to an industrial conveying system. a) Discuss and illustrate the difference between reactive, preventative, and predictive maintenance. b) Describe several of the techniques that could be used to develop a predictive maintenance system for the conveyor system. Consider some of the sensing techniques that might be used and what parameters might be measured to detect component degradation. c) If the predictive maintenance system described in b) detects that the conveyor system is vibrating abnormally, discuss what condition this could indicate and what maintenance might be required.
plz provide answer for this part only describe the distribution system used in the residential sector of Pakistan having at least 5 Km Length and minimum of 300 consumers attached with.
1. Electrical explosions directly into the face of a person working on or near energizedelectrical equipment can and will cause serious injury or death. OSHA laws and NFPA70E have strict safety requirements for working on electrical equipment. The basicrules are to turn off the power before working on the equipment and to wear the propertype of nonflammable clothing. To further provide safety for the worker, the NationalElectrical Code has a requirement pertaining to arc-flash hazard warning. This requirement is found in of the NEC.
The terminal points determined by pi/2, pi, -pi/2, 2pi are __________, ________, ___________, and ___________, respectively.
Please answer in short like it definitely don't reject in shorts please Please
4. A decorative display uses inexpensive mass produced colored lights having constant failure rate of 1000 per million per day. Assume that such a display is designed with 2000 such lights that are all turned on at the same time. The lights are so connected that failure of one does not affect the operation of others. a) How many lights can be expected to still be operational after 90 days? b) Determine the mean time to failure of any given light. c) Determine the probability that any given light will fail within the first 100 days after turn on and also that 20 lights will do likewise. d) Repeat part c) replacing 1000 days for 100 days. e) Determine the time that can be expected to elapse (from turn on) before the display has only one operational light left.
Solar Panel Pros And Cons
please sir solve these 2 questions, thanks alot
Electrical Engineering a) A 240V single phase circuit is run in conduit in 2 core 70°C PVC/PVC cable having live conductor of 2.5 mm? (Ioperating is approximately 20A) and protection conductor cable (cpc) of 1.5 mm?. If the circuit is protected by 30 HRC fuse, with circuit length of 55 m, and ZE is 0.8 2. EVALUATE whether the initial c.p.c. size provided is adequate. Given 2 core PVC/PVC bunched cable impedance is (R1 + R2) = 26.9 m2/m and k = 115.
State two factors considered when selecting pv module site for domestic installation