A simple Rankine cycle works between the boiler pressure of 4 Mpa and condenser pressure of 30 bar. The steam is dry saturated before the throttling in the turbine. Determine the Rankine cycle efficiency

A simple Rankine cycle works between the boiler pressure of 4 Mpa and condenser pressure of 30 bar. The steam is dry saturated before the throttling in the turbine. Determine the Rankine cycle efficiency

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A simple Rankine cycle works between the boiler pressure of 5 MPa and condenser pressure of 5 kPa. The steam is dry saturated before the throttling in the turbine. Determine Rankine cycle efficiency work ratio specific steam consumption
n an ideal rankine cycle. Steam is generated at 4.1 mpa and 480C. The condenser is at 32C. For an engine with the same end states, determine its thermal efficiency, steam rate, and mep. Considering the engine only, assume the brake engine efficiency to be 78%, the generator efficiency 92%, the steam flow rate is 163,600 kg/hr. Compute the output of the combined unit.
In a steam power cycle, the steam supply is at 15 bar and in a dry and saturated condition.The condenser pressure is 0.4 bar. Calculate the Carnot and Rankine efficiencies of the cycle.Ignore the work of the pump.
4. Consider a simple ideal Rankine cycle. The pressure of the boiler and the condenser are 3 Mpa and 10 kPa respectively. The temperature of the steam entering the turbine is 350°C, and the quality of mixture leaving the turbine is 0.8. Calculate the back work ratio, in %. 0.4% - 0.5% · 0.3 % - 0.6%
In an ideal reheat-rgenerative cycle, steam enters the turbine at 6 MPaa and 400 degrees Celsius. After expansion to 1.4 MPaa steam is withdrawn and reheated to 300 degrees Celsius . Extractions for regenerative heating occur at 0.15 MPaa and 1.4 MPaa and the condenser pressure is 0.1 MPaa. Use mass flowrate of 1 kg/s.
An ideal Rankine cycle operates between a steam boiler pressure of 18 MPa and a condenser temperature of 42 °C. The steam leaving the boiler is a saturated vapor. The net power generated by the cycle is 150 MW. What is the mass flow rate of steam? What is the cycle efficiency? Use the formula: n=Wnet/Qin.
In the ideal Rankine cycle shown, the boiler pressure is 6 MPa and the condenser pressure is 8 kPa. The steam enters the turbine at 440°C at a mass flow rate of 7.0 kg/s. In your written solution, (a) determine the enthalpies at states 1, 2, 3, and 4; (b) draw the T-s diagram with the states in the correct region; (c) determine the cycle power output; and (d) the cycle thermal efficiency.
In a Rankine cycle steam enters the turbine at 2.5MPa (enthalpies and entropies given) and condenser of 50KPa (properties given), what is the thermal efficiency of the cycle? At 2.5MPa: hg = 2803.1 sg = 6.2575, At 50KPa: sf = 1.0910 sfg = 6.5029 hf = 340.49 hfg = 2305.4 vf = 0.0010300
A Brayton cycle is used to estimate the performance of an aircraft engine with nitrogen as the working fluid. The engine generates a net power of 10 MW. Nitrogen enters the compressor of the engine at 250 K and 80 kPa and is compressed to a pressure of 400 kPa. The gas exits the turbine of the engine at 450 K and 80 kPa.a. Calculate the mass flow rate of nitrogen through the engine.b. Calculate the thermal efficiency of the cycle.c. Determine the irreversibility per unit mass for each process and for the cycle if TH = 1500 K and TL = To = 250 K.d. Which process has the largest irreversibility?
Consider a simple ideal Rankine cycle. What happens when the condenser pressure is raised while keeping the turbine inlet state the same?
14