4. Consider a simple ideal Rankine cycle. The pressure of the boiler and the condenser are 3 Mpa and 10 kPa respectively. The temperature of the steam entering the turbine is 350°C, and the quality of mixture leaving the turbine is 0.8. Calculate the back work ratio, in %. - 0.4% 0.5% 0.3 % 2.

4. Consider a simple ideal Rankine cycle. The pressure of the boiler and the condenser are 3 Mpa and 10 kPa respectively. The temperature of the steam entering the turbine is 350°C, and the quality of mixture leaving the turbine is 0.8. Calculate the back work ratio, in %. - 0.4% 0.5% 0.3 % 2.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steam Rankine cycle operates between the pressure limits of 1500 psia in the boiler and 3 psia in the condenser. The turbine inlet temperature is 800°F. The turbine isentropic efficiency is 90 percent, the pump losses are negligible, and the cycle is sized to produce 2500 kW of power. How much error is caused in the thermal efficiency if the power required by the pump were completely neglected? Use steam tables. The error caused in the thermal efficiency if the power required by the pump was completely neglected is %.
Q2) Consider a steam power plant that operates on a simple Rankine cycle and has a net power output of 45 MW. Steam enters the turbine at 7 MPa and 500°C and is cooled in the condenser at a pressure of 10 kPa by running cooling water from a lake through the tubes of the condenser at a rate of 2000 kg/s, note that steam enter pump with enthalpy 191.81kJ/kg and enter turbine with enthalpy 3411.4kJ/kg and entropy 6.8 kJ/kg.k assuming an isentropic efficiency of 87 percent for both the turbine and the pump determine (a) the thermal efficiency of the cycle, (b) the temperature rise of the cooling water.
Do it ASAP
Thermodynamics
An ideal RANKINE cycle delivers 210 MW of power. Steam enters the turbine at 10 MPa and500C and is cooled in a condenser at 10 kPaa. Determine the thermal efficiency of this cycleb. Mass flow of waterc. Heat rejected in the condenserd. Work inputted to the pump (remember the volume is constant)
A power plant operating on an ideal Rankine cycle has steam entering theturbine at 500°C and 2 MPa. If the steam enters the pump at 10 kPa, calculate the thermal efficiency with pump work included, the thermal efficiency neglecting pump work, and the percentage error in efficiency neglectingpump work.
Consider a steam power plant operating on the ideal Rankine cycle. Steam enters the turbine at 3 MPa and 350°C and is condensed in the condenser at a pressure of 10 kPa. Determine
The production well of a typical geothermal power plant is at 230°C saturated liquid and ground water flow rate of 230kg/s with separator pressure of 0.5MPaa while its condenser pressure is at 0.01MPa. the turbine and generator efficiencies are 83% and 87% , respectively. Sketch the T-s diagram of the system. Determine the amount of mass flowing into the reinjection well from the separator, generator output, heat rejection in the condenser and overall plant efficiency.
In the ideal Rankine cycle shown, the boiler pressure is 6 MPa and the condenser pressure is 8 kPa. The steam enters the turbine at 440°C at a mass flow rate of 7.0 kg/s. In your written solution, (a) determine the enthalpies at states 1, 2, 3, and 4; (b) draw the T-s diagram with the states in the correct region; (c) determine the cycle power output; and (d) the cycle thermal efficiency.
A 12,000 MW gas turbine operating in the simple open cycle has an exhaust gas flow of 80 kg/s. The gas enters a wasteheat recovery boiler at 400°C and leaves at 130°C, specific heat of the gas is 0.85 kJ/kg - K, heat required to produce 1kg of steam at 4.5 MPa and 320°C from feedwater at 110°C is 3.5 kJ. A. Calculate the quantity of steam that can beproduced in kg/hr. B. If the steam produce from this waste heat recovery boiler is used to run a steam turbine-generator setwith a combined steam rate of 6.4 kg/kW-hr, what additional kW capacity can be obtained at no fuel cost?
Hi, I need help with this practice problem for Thermodynamics
This is thermodynamics 2