A simple power system is shown in this Fig. The generator (480 V, 10 kVA) is connected to an ideal step-up transformer (1:20), a transmission line (R=20 Ohm and X=60 Ohm), step down transformer (40:1) and a load (R= 25 Ohm and X=10 Ohm) the base values for this system are chosen to be 480 V and 10 kVA at the generator. Calculate the per unit reactive power for the load. line oad Zoad 202 j60 N Zine 480 0° V 6-Per-unit Systems Calculations.pdf - Adobe Acrobat Reader DC (32-bit) Select one: O a. 0.079 O b. 1.63 O c. 1.33 O d. None of the above O e. 0.25

A simple power system is shown in this Fig. The generator (480 V, 10 kVA) is connected to an ideal step-up transformer (1:20), a transmission line (R=20 Ohm and X=60 Ohm), step down transformer (40:1) and a load (R= 25 Ohm and X=10 Ohm) the base values for this system are chosen to be 480 V and 10 kVA at the generator. Calculate the per unit reactive power for the load. line oad Zoad 202 j60 N Zine 480 0° V 6-Per-unit Systems Calculations.pdf - Adobe Acrobat Reader DC (32-bit) Select one: O a. 0.079 O b. 1.63 O c. 1.33 O d. None of the above O e. 0.25

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a device has an average power rating of 1200W and deisgn to operate 250V rms line. detrmine the effective resistance if the power socket available has 115V rms line and uses a step up ideal transformer from 115V to 250V.
Q4//a. A 600 KVA one phase transformer when working at unity p.f has an efficiency of 92% at full load and also at half full load. Determine its efficiency when it operates at unity p.f and 60% of full load. b. The voltage in an alternating current circuit at any time t seconds is given by v=60 sin 40 t volts. Find the first time when the voltage is (i)50 v (ii)15 v
Question 2. Consider a 10 kTA, 200 400 V, 50 H; single-phase transformer has the following test results: O.C. test : 200 V, 0.7.4, 55 W (L.V. side) S.C. test: 20 V, 25 A, 80 W (H.V. side) Determine : i) The efficiency at 60 % of full-load at 0.7 lagging power factor. ii) The voltage regulation on fiull-load at 0.8 leading power factor.
A step-up transformer connected to a 180 V line is used to supply a hydrogen-gas discharge tube with 6.0 kV (rms). The tube dissipates 77 W of power. (a) What is the ratio of the number of turns in the secondary winding to the number of turns in the primary winding? N₂ Np (b) What are the rms currents in the primary and secondary windings (in A)? Ip = Is = A A (c) What is the effective resistance (in 22) seen by the 180 V source? Ω
8. The two winding transformer and the autotransformer of the circuit shown in Figure are ideal. Determine the conducting and transformed currents of auto transformer. N1=200 NBC=20 N2=100 NBA=30 10A B 200 V 50,Hz C N1: N2
a 15 kVA closet transformer located inside a building is used to step down the voltage for the building. it is connected to a primary 9800V AC power source. The ratio of the number of primary windings to the number of secondary windings on the transformer is 60 to 15. what is the voltage provided to the building? what is the amount of current provided to the building? if the building consumes 3200W of power, what is it's power factor? what is the phase angle of the secondary power source in the building?
Following are the results of a test carried out on a 230/600 V single phase, 7.5 kVA transformer. O.C. Test : 230 V, 1.2 A, 280 W, on L.V side S.C. Test : LV winding is shorted. 26 V, 11A, 155 W, H.V. Both the full load efficiency and full load regulation of the transformer on the side are 0.8 lagging p.f Search on.
Problem 3: A 60 Hz, 13.5kV/240V, single-phase ideal transformer is used to step-down the voltage of a distribution system. If the low-voltage side of the transformer is to be kept at a constant magnitude of V₂ - 240 V determine the following quantities: a) the value of the load I impedance (connected to the low-voltage side) that will cause the transformer to be fully loaded; b) the value of the load impedance found in a) referred to the high-voltage side of the transformer; c) the value of the load current referred to the low-voltage side of the transformer; and d) the value of the load current referred to the high-voltage side of the transformer.
Q8 Please solve this question correctly in 15 minutes in the order to get positive feedback Please provide me hundred percent correct answer. If you provide solutions correct I will give you thumbs up