A simple pendulum is pivoted at O and is free to swing in the vertical plane of the plate. If the plate is given a constant acceleration a = 2.2 m/s? up the incline e = 30°, find the steady angle ß assumed by the pendulum after all initial start-up oscillations have ceased. Neglect the mass of the slender supporting rod. Answer: ß = i

A simple pendulum is pivoted at O and is free to swing in the vertical plane of the plate. If the plate is given a constant acceleration a = 2.2 m/s? up the incline e = 30°, find the steady angle ß assumed by the pendulum after all initial start-up oscillations have ceased. Neglect the mass of the slender supporting rod. Answer: ß = i

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The circular shaft AB consists of a 24.2 mm diameter solid steel cylinder in which a 11.4 mm diameter hole has been drilled from end B up to point C. The shaft is attached to fixed supports at each end, and a 150 Nm torque is applied at C. The torque reaction at A is 53.0 Nm. What is the internal torque in segment AC of the shaft? Input your answer as a value only in Nm to one decimal place without +/-sign. L₁ L₂ A 150 Nm B
A solid constant-diameter circular shaft is subjected to the torques of TA = 470 Ib-ft, Te = 1090 lb ft, Tc = 840 Ib-ft, and Tp = 220 lb ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in Section 6.6. (b) If the allowable shear stress in the shaft is 5200 psi, what is the minimum acceptable diameter for the shaft?
The figure shows a sphere resting in a smooth Vshaped groove and subjected to a spring force. The spring is compressed to a length of 125 mm from its free length of 150 mm. If the stiffness of spring k= 10 N/mm and weight of sphere is 100 N. Determine the contact reactions at the point A and B. 30° eeee • W 60° 1
Calculate the support reaction at point A and B of the given figure. kindly show your complete solutions.
Consider the portal frame shown in the figure and assume the modulus of elasticity, E = 3.5 x 104 MPa and the moment of inertia, I = 9 × 108 mm4 for all the members of the frame. A 2m 1650 kN/m ot - 2000 KN P E,I Q E,I R E,I S 4m 4m The rotation (in degrees, up to one decimal place) at the rigid joint Q would be
A solid constant-diameter circular shaft is subjected to the torques of TA = 490 lb·ft, TB = 1080 lb·ft, TC = 830 lb·ft, and TD = 240 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in Section 6.6. (b) If the allowable shear stress in the shaft is 7400 psi, what is the minimum acceptable diameter for the shaft?
A solid constant-diameter circular shaft is subjected to the torques of TA = 460 lb·ft, TB = 1000 lb·ft, TC = 880 lb·ft, and TD = 340 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in Section 6.6. (b) If the allowable shear stress in the shaft is 7200 psi, what is the minimum acceptable diameter for the shaft?
A uniform bar AB is resting in a horizontal position on smooth inclines as shown below. Determine the load P that will hold the bar in equilibrium. Also, determine the reactions at A and B. 411 N 2m 7m 1m A 60° 450