A silicon photodiode is connected to an op-amp as indicated. Under an illuminance of 500 lux, the photocurrent I, is 80 nA. R = 1ΜΩ M V out a) Write down the values of 1₁, 12 and Ip. From these values, deduce the output voltage. b) Briefly describe how this circuit works. c) Will this circuit work under sunlight? The illuminance of sunlight is about 100,000 lux. You may assume the photocurrent respond linearly with incident light flux, and the op-amp is powered between 9V alkaline cell. (i.e., V* = 9V, V at ground).

A silicon photodiode is connected to an op-amp as indicated. Under an illuminance of 500 lux, the photocurrent I, is 80 nA. R = 1ΜΩ M V out a) Write down the values of 1₁, 12 and Ip. From these values, deduce the output voltage. b) Briefly describe how this circuit works. c) Will this circuit work under sunlight? The illuminance of sunlight is about 100,000 lux. You may assume the photocurrent respond linearly with incident light flux, and the op-amp is powered between 9V alkaline cell. (i.e., V* = 9V, V at ground).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

**Experiment No. 6: Comparator Circuit َ1- If the voltage reference is in the middle of the sine wave form, it mean that the output will be : a ) square wave b ) still sine wave c ) triangle waveform 2- if the voltage reference is greater than voltage voltage input, the output will be: A) negative output B) positive output 3- The voltage reference is 5V and the voltage input is 1vp-p, the signal is ? a) always in positive output b) always in negative output
B scale shown in the figure below in it The internal resistance of the coil is Rm = 200, the parallel resistance of the col is Rsh=200, the current of the maximum gradient is Im=1mA, the forward resistance of each diode is 50. If you know the input voltage, it was a wave in a triangular shape, its maximum height, calculate at a frequency of 507 A-The value of the series resistance RS to obtain the maximum deviation in the gradient-The sensitivity of the voltmeter Sac 3-Mention the usefulness of each of the resistors (RS, RS) WW= www R₁ Rsh 19
Parallel clipper circuit is given in the figure. Input voltage , Vs= 10 V. Find the voltages obtained on R1, RL and diode. (Note: Take the voltage amplitude as +10, -10V. Take the division value per oscilloscope screen as 5 ms. You can get the function generator frequency value as 50 or 100 Hz.) R-200 20 R |2 2K0 201
Problem 1: Di and D2 are battery modeled diodes of 0.7 V. If 'V;’ is a sinusoidal signal with 1 kHz frequency and amplitude voltage of 40V, 1. Plot Vo, Ipi, and Ip2 versus 'V¡’ 2. Plot Vo versus time D1 D2 3 k2 9 k2 V; Vo 25 V 5 V
A step down converter is operated with a duty cycle of k = 0.75. The input voltage is Vs = 20V, and the load is: L = 5mH, R = 1502. The minimum inductor current is I₁ = 0.1A. The maximum inductor current is: Select one: a. 1.9 A b. None of these OC. 0.9 A O d. 1.1 A Oe. 2 A
Calculate the rms value of the output voltage of an AC-AC converter with the following specifications. Vs—110*sqrt(2)*sin(wt), Alpha Pi/6
B scale shown in the figure below in it The internal resistance of the coil is Rm = 200, the parallel resistance of the coll is Rsh=200, the current of the maximum gradient is Im=1 mA, the forward resistance of each diode is 50. If you know the input voltage, it was a wave in a triangular shape, its maximum height, calculate 20 at a frequency of 50 A- The value of the series resistance RS to obtain the maximum deviation in the gradient- The sensitivity of the voltmeter Sac 3-Mention the usefulness of each of the resistors (RS, RS) W R₁
N
Exercise 2: Calculate the following i. Current flowing through the circuit. (Irms) ii. Current flowing through the resistors R9, R10, R11. (Irms) iii. Calculate the peak to peak- peak voltage (Vpk-pk) and peak-peak current (I pk-pk) iv. Calculate the time period of the waveform
I need the answer quickly
Q/ Draw the input and the output waveform of the circuit below and analyze the signal flowing in both half-cycles Using two different colors, and label the voltage on the waveform, then determine Vay and Vrms (Vin=5V, frequency= 1kHz) 17 ww
Find the Current in the Circuit in Miliampares