(A shunt DC motor has a total armature resistance value for all conditions as Ra= 2 Q and under full load conditions (nominal load) amature current is Ia = 15 A. The nominal temminal Voltage for the motor is V-300 V and total value for field circuit resistance for all conditions is Rf-100Q Under full load conditions (nominal load), find the internal generated Voltage (EA), field current (excitation circuit current) (If), starting current (maximum value of starting curent flow, from electrical source) (Ime), electrical input power (Pin) supplied from the electrical source under full load (nominal load) conditions. Be careful about your solutions to be written readable and write the answers inside boxes as it was shown below.) EA If- Iaun (Iyv) = Pin -

(A shunt DC motor has a total armature resistance value for all conditions as Ra= 2 Q and under full load conditions (nominal load) amature current is Ia = 15 A. The nominal temminal Voltage for the motor is V-300 V and total value for field circuit resistance for all conditions is Rf-100Q Under full load conditions (nominal load), find the internal generated Voltage (EA), field current (excitation circuit current) (If), starting current (maximum value of starting curent flow, from electrical source) (Ime), electrical input power (Pin) supplied from the electrical source under full load (nominal load) conditions. Be careful about your solutions to be written readable and write the answers inside boxes as it was shown below.) EA If- Iaun (Iyv) = Pin -

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q5- Adjust a fire angle for a three-phase full-wave semi-controlled converter to feed the separately exciter DC motor to get a load torque can be reached to 750 rpm. When the supply voltage of converter is 150 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 2 and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.
To modeling separated excited DC motor by transfer function, you need to Trus Fuc block to get the represent armature current la field current If Speed Wr electromagnetic Torque Te *
The armature circuit of a free excited direct current motor with a nominal voltage of 600 V is fed from an adjusted direct voltage source. The excitation circuit is also powered from a regulated voltage source. It is used in an application that requires motor speed adjustment. The speed of the motor at the nominal armature voltage was measured as 1600 rpm. All losses of the motor and voltage source and the effect of armature reaction are neglected. It is accepted that the engine is not saturated.Answer the questions below.a) Draw the armature and excitation circuit of the motor and write the formulas for the equivalent circuit.b) If the load moment of the motor at the nominal armature voltage is 420 Nm, then calculate the armature current and the input power of the motor.c) If the armature voltage of the motor is kept constant at 600 V and the excitation current is decreased until the speed reaches 4000 rpm, then calculate the shaft moment. Show this working area on the M = f (W) axis.
(A shunt DC motor has a total resistance value for all conditions as Ra= 2 Q and under full load conditions (nominal load) armature current is Ia = 10 A. The nominal terminal Voltage for the motor is Vr-300 V and total value for field circuit resistance for all conditions is Rf=150 Q. Under full load conditions (nominal load), find the internal generated Voltage (EA), excitation circuit current (field current) (If), (total supply current flow, from electrical source) line current (IL), electrical input power (Pin) supplied from the source. Be careful about your solutions to be written readable and write the answers as it was shown below inside boxes.) EA = If = IH (IL) = Pin =
Q1 Describe the Characteristics, characteristics, efficiency calculations, their applications Of DC Motors in detail
Consider a shunt DC motor with an armature resistance RA =0.2N and terminal voltage VT = 160 V. The motor rated speed is 1800 RPM. The total field resistance 240 Q. Assume No armature reaction in this machine. The variation of the armature terminal voltage as a function of the field current is measured under no-load conditions and shown below: IF (A) EA (V) 1.0 141 0.0 0.6 125 These values were taken at speed n= 1800 RPM 0.1 0.2 0.3 0.4 0.5 0.7 0.8 0.9 30 60 85 102 115 132 137 140 If the motor is driving a load at an armature current IA=60 A, its rotational speed is 1517 RPM, with rotational losses of 848 Watt. What torque is induced by this motor? Select one: O a. Induced Torque = 62 N.m O b. Induced Torque = 56 N.m O c. None O d. Induced Torque = 51 N.m.
Please solve all subdivisions please
For a 18600W 2400rpm DC motor, the following values are given: Ra = 0.089 2 (value at room temperature (250C)), La = 0.00144 H, KT = 0.85 Nm / A and KV = 0.851 V / (rad / s)), (In calculations Use the hot resistance values at 1000C.) (Take the rated field winding losses as Wf= 210W.) If this DC machine is operating as a motor with rated flux at rated speed, calculate the rated torque (TR), rated current (IR), rated voltage (VR), efficiency (n) at the rated point, taking into account the winding losses. Find the speed (@NL) of this motor in no-load condition. TR Nm IR А VR V Eff = % ONL= rpm
A 4 pole10V, DC shunt motor operates on a load current 10A, having wave connected armature with 200 conductors. The flux per Pole is 25 m Wb. Resistance of shunt field winding is 1 ohm and resistance of the armature is 0.15 ohm. a) what would be the back emf?
The supply voltage to a DC motor is 160V. If the back emf Ez=155V and the armature resistance A6 is 0.250, the armature current is a) 5A b) 10A c) 15A d) 20A 1800 ro/min The frequency
Consider a separately-excited DC motor with an armature resistance RA = 0.2 N and terminal voltage VT = 130 V. The motor rated speed is 1000 RPM. The field winding supply VF= 24 V and the field resistance is adjustable. The motor has compensating windings and interpoles. 0.3 IF (A) EA (V) 0.0 0.1 0.2 0.4 0.5 0.6 0.7 0.8 30 102 These values were taken at speed n= 1000 RPM 60 85 115 124 130 134 If the motor is driving a load at rated armature current IA = 60 A, with Radi +RF = 40 2. Find the speed of rotation ofthe motor in RPM.Select one: a. Speed n = 952 RPM b. None c. Speed n = 1051 RPM d. Speed n = 1000 RPM
A 500 V DC shunt motor takes 4 A at no-load. The shunt field winding resistance and the armature winding resistance are 250 and 0.2 respectively. Find the efficiency when the motor draws a current of 10 A at full load.