A short transmission line connects a step-up transformer on the source side with a series impedance of j0.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary). The turn ratio of the step-up transformer is 1:10 and a no-load primary voltage of 13.2 (line-to-line) kV. The step-down transformer has a turn ratio of 15:1 and it has a Y-connected, balanced load of 0.667 +j 0.111 ohms connected to its secondary side. Assuming an ideal transmission line, the effective impedance of the system seen by the source would be: A. 7.65 + j0.883 B. 15 + j12.5 C. None of the other choices are correct D. 0.765 + j0.883 E. 1.5 +j1.25

Q: A short transmission line connects a step-up transformer on the source side with a series impedance…

A: To find the real power absorbed by the load, we first need to determine the voltage and current at…

Q: If the open circuit voltage is 225V and the full load voltage is 200V, then the percentage…

A:

Q: Ql-phase step down transformer 1250 KVA, 110002200 V, 50 Hz. The resistance iphase and leakage…

A:

Q: Ql-phase step down transformer 1250 KVA, 11000/2200 V, 50 Hz . The resistance /phase and leakage…

A: (i) The per-phase secondary voltage in the star-connected secondary winding can be calculated as,

Q: A step-down transformer is one at which the secondary voltage is higher than the primary voltage.…

A: Tranformer is a constant frequency and constant power device . transformer consists of two windings…

Q: Ideal transformer with primary of 200 turns and secondary of 100 turns. The primary is connected to…

A: secondary voltage = primary voltage×secondary turnsprimary turns. current in load = power delivered…

Q: The number of turns on the primary and secondary windings of a 1-p transformer are 350 and 42…

A: Given : A single phase transformer having number of turns on the primary and secondary winding are…

Q: Consider a 7200V/240V transformer with center-tap on the secondary that is a grounded neutral. If a…

A: Given: Center-tap transformer with neutral grounded with rating 7200V/240V P1=1.0 kWP2=0.5 kW

Q: A transformer shown in Figure 10 is needed that will cause an actual load resistance of 250 to…

A: (a) Redraw the given circuit diagram.

Q: The apparent power in primary and secondary side of the distribution transformer remains the same at…

A: Given  Apparent power is same in both primary  and secondary  of transformers  Ture or false

Q: A 50 Hz, Scott connected transformer supplies an unbalanced two phase load at ( 400 V) per phase.…

A: Scott connection is used to convert a balanced three-phase into balance 2 phases or vice versa. it…

Q: A short transmission line connects a step-up transformer on the source side with a series impedance…

A: A Short transmission line connected to (i) a step-up transformer on the source side with a series…

Q: mer has primary and 80 turns on the secondary. The primary 2. A 100 KVA transf and secondary…

A: Given data, The rating is 100kVA. Primary resistance  = 0.3Ω Secondary resistance  = 0.1Ω Primary…

Q: A short transmission line connects a step-up transformer on the source side with a series impedance…

A: Given  A short transmission line connects to (i) a step-up transformer on the source side with a…

Q: A transformer has an input voltage of 2kV and a step-down ratio of 5:1. The primary and secondary…

A: According to question: The equivalent resistance with respect to secondary winding is calculated as…

Q: Determine the ratio of the kW output of transformer A to the kW output of transformer B. Both…

A:

Q: At the end of a one-phase supply line with a series impedance of 1+j2 ohms, a 50 kVA, 2400/240 volt,…

A:

Q: Q 3-phase step down transformer 1200 KVA , 11000/2200 V, 50 Hz .The resistance /phase and leakage…

A: Given values are =

Q: Questior A short transmission line connects a step-up transformer on the source side with a series…

A: The answer as given below steps:

Q: If the open circuit voltage is 225V and the full load voltage is 214V, then the percentage…

A: Percentage regulation is given by R    R = (VOC - VFL ) / VFL    VOC = Open circuit voltage    VFL =…

Q: A step-up transformer is designed so that the output of its secondary winding is 2,200 V (rms) when…

A: Given: A step up transformer is designed to have V1=210 VV2=2200 V

Q: In a single phase transformer, when no-load voltage is 230V and full load terminal voltage is 220,…

A:

Q: Solve it quickly please

A: From the above problem we have given  Hence symmetrical component of voltage is given as

Q: Ql-phase step down transformer 1250 KVA, 1 1000/2200 V, 50 Hz .The resistance /phase and leakage…

A:

Q: A short transmission line connects a step-up transformer on the source side with a series impedance…

A: For ideal transmission line the loss in transmission line is zero . So there is no active and…

Q: Ql-phase step down transformer 1250 KVA, 11000/2200 V, 50 Hz .The resistance /phase and leakage…

A:

Q: Puestion Draw approximate transformer quantities. :- model into all of secondary referred to…

A:

Q: 6. 150 kVA, 2800-240 V, 50 Hz transformer. Reg.Ls = 0.0082N , Xeq.Ls = 0.02230 Step down transformer…

A: Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

Q: For a 250 [kVA] practical transformer with 4160 [V) primary and 480 [V] secondary, the base…

A:

Q: Ql-phase step down transformer 1250 KVA, 11000/2200 V, 50 Hz .The resistance /phase and leakage…

A:

Q: Whenever a conductor is placed in a magnetic field it experiences a force, this is related to motor.…

A:

Q: 2.Fringing effect is a phenomena occurs in ........... (a) Transformers. (b) Electrical field. (c)…

A: We are authorized to answer only one question at a time since you have not mentioned which question…

Q: If the core loss of single phase transformer at full load is 98 W, then the core loss at 25% of load…

A: In the transformer core losses independent of load.   We can also say in the transformer core losses…

Q: The apparent power in primary and secondary side of the distribution transformer remains the same at…

A:

Q: A transformer has 520 primary turns and 160 secondary turns. The primary and secondary resistances…

A: First we will refer secondary side resistance and reactance to primary side and than we will find…

Q: 3. Single-phase T1-transformer with a power of 500 kVA and a single-phase T2- with a power of 400…

A: Power factor: This tells how much active power is utilized by the circuit from the apparent power.

Q: N1: N2 In-1A Vac 60 Hz Ver Center tapped 5000uF D2 Output Waveform: Vpp Voc 12V

A:

Q: A single phase 9.6 kVA, 500 V / 1.5 kV transformer has an impedance of 1.302 Ω with respect to…

A: GivenKVA of the transformer =9.6 KVA=0.0096 MVAPrimary side voltage=500 v=0.5 Kvsecondary side…

Q: A low voltage distribution transformer feeds two different loads with a three-phase line. The…

A: Given Data is-                     Nominal Voltage V=400 volt The total length of the feeder L=500 m…

Q: A short transmission line connects a step-up transformer on the source side with a series impedance…

A: Short Transmission Line: A short transmission line is one with an effective length of less than 80…

Q: A short transmission line connects a step-up transformer on the source side with a series impedance…

A: For ideal transmission line there is no loss in transmission line hence resistance and reactance of…

Q: A non-ideal 1-phase transformer has turns ratio 5:1 with 120Vac primary.  The primary impedance is 1…

A:

Distribution System

The final stage in the delivery of the electric power is the electric power distribution system. From the transmission system to the individual customers it carries electricity. The distribution system is connected with the transmission system and is used to lower the voltage of the transmission to medium voltage in the range of 2 kV to 35 kV with the help of transformers. This medium voltage to the distribution transformers located near the customer's premises is carried by the primary distribution system lines. These distribution transformers in turn lower the voltage to utilization voltage used in lightings, household appliances, industrial equipments etc. Through secondary distribution lines often several customers are supplied from one transformer. It is through service drops, the commercial and residential customers are connected to the secondary distribution system lines. Customers who demand a larger amount of power can be connected directly to the primary distribution system level or the sub-transmission level.