A sheet of zinc (Zn) that is 4 cm wide by 10 cm long is placed in an hydrochloric acid solution (HCI). The initial thickness of the zinc sheet is 3 cm, and the corrosion current measured on the surface is 9.8x 10-3 amperes (C/s). What is the thickness of the plate (in cm) after 45 weeks? ou may assume that the corrosion occurs on only one side of the sheet.

A sheet of zinc (Zn) that is 4 cm wide by 10 cm long is placed in an hydrochloric acid solution (HCI). The initial thickness of the zinc sheet is 3 cm, and the corrosion current measured on the surface is 9.8x 10-3 amperes (C/s). What is the thickness of the plate (in cm) after 45 weeks? ou may assume that the corrosion occurs on only one side of the sheet.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

A steel railroad bridge uses a zinc sacrificial anode to limit the extent of oxidation of the steel. If a 7.7 kg anode is completely ozidized to Zn2+ over the course of 12.1 years, compute the average current flowing through the anode.
Assume a concentration cell with a zinc anode and a zinc cathode. The anode is surrounded by a 100 ml ZnSO4 solution of 0.01 mol/l concentration. The cathode is surrounded by a 100 ml ZnSO4 solution with a concnetration of 1 mol/l. A salt bridge ensures neutrality of both solutions during the reaction. This system can be described in short-hand notation as: Zn(s) | Zn²+ (aq) (0.01 M) II Zn²+ (aq) (1 M) I Zn(s) The temperature is 25°C. Part D Determine the initial voltage of this concentration cell. Provide your result with three significant figures in the appropriate units. AE 59.2 mV Submit Previous Answers Correct
A current of 6.6 A is passed through a solution of AgNO3 to electroplate it onto a surface. Calculate the mass, in grams, of pure silver deposited on the surface after 77 seconds.
When water was electrolyzed for 18.4 min; 25 mL of oxygen was collected at the anode at 22°C the total pressure of the oxygen was 1.187 atm. Determine the current that was used to produce the gas.
How many seconds are required to deposit 0.252 grams of tin metal from a solution that contains Sn* ions, if a current of 0.899 A is applied.
An object with a surface area of 24.1 cm224.1 cm2 is to be plated with nickel. A current of 7.93 A7.93 A is applied to a solution containing nickel in the +2+2 oxidation state. Calculate the time required to coat the object with an even layer of nickel that is 9.71×10−3 cm9.71×10−3 cm thick. The density of nickel is 8.91 g/cm3.
below. questions 8 for the electrolysis of molten lead(II) chloride (PbCl₂) as seen in the diagram Anode + Voltage source Porous screen Molten PbCl₂ e Cathode
A metallurgist want to gold-plate a thin sheet with the dimensions 1.5in, 8.5in, 0.0012 in. The gold plating must be 0.0020in thick. I am confused on how to solve this question. How long will it take to plate the sheet from AuCN using a current of 7.00A? Can someone help me
This part is on electrolysis: Calculate the mass of copper deposited during the electrolysis of a CuSO4 solution if a current of 20.0 amps flows for 35.0 minutes. The molar mass of copper is approximately 63.55 g/mol.
A small part with a surface area of 3.0 cm2 is plated with a gold coating that is 5.00x10-4 mm thick. The density of gold is 19.32 g/cm3. a) What mass of gold is in this coating? b) If a barrel plating run has 6000 of these parts in a single barrel, how long would the run take if the current was 15 A? (Gold is effectively plated from Au+(aq)
You have a 2.50 cm diameter sphere that you would like to have plated with platinum metal. How long will it take to electroplate a 40.0 micron thick coating onto the sphere using Pt+2 and a current of 0.500 amps? The density of platinum is 21.45 g/cm3. 1 micron = 1.00×10–4 cm.[hint: Calculate the difference in volume of the coated and uncoated spheres and then use the density information to determine your answer.]Time Required = Answer minutes
In the Hall-Heroult process, a large electric current is passed through a solution of aluminum oxide (Al,0,) dissolved in molten cryolite (Naz AIF, resulting in the reduction of the Al,0, to pure aluminum. Suppose a current of 8300. A is passed through a Hall-Heroult cell for 29.0 seconds. Calculate the mass of pure aluminum produced. Be sure your answer has a unit symbol and the correct number of significant digits. ロロの