A shaft is to be designed for a linkage of a windshield wiper mechanism for a truck as shown in Tigure below. A 20-N force is applied to lever 1 (I'1) by an adjacent link. The reaction force (F2) on lever 2 is transmitted to another link. Requirement: Select suitable bearings points A & D.

Q: Numerical 4. DESIGN OF BELT CONVEYOR SYSTEM WITH THE FOLLOWING SPECIFICATION Material to be carried…

A:

Q: Q4-A square threaded screw is required to work against an axial force of 6000N and has following…

A: Given       Force, F = 6000 N Diameter, d = 32 mm       Pitch, p = 4 mm Find   Torque, T

Q: Problem 4. For the belt drive shown below calculate the contact angle 0, if: D = 100 mm; d 3 30 тm;…

A:

Q: Determine the degree of freedom of the following mechanisms. Show all calculations and detail

A:

Q: solve/ show solution for given answer equations  kb = (Ab*Eb)/ g and kc = (Ac*Ec) / g

A: Given a bolted connection between two steel plates with specific dimensions and a torque of 57…

Q: Calculate the capacity ol a bucket conveyor. The parameters are as follows.Belt speed 2.5 m/sec,…

A:

Q: rom the 4-figure electric motor taken, 500Nm torque steps B and C by 200Nm and 300Nm is transmitted.…

A: Given

Q: A linear actuator having a in single-thread Acme screw is used to raise a load of 1600 lb. A plain…

A: Given:The diameter of the thread, The value of the load, The mean diameter of the thrust collar, The…

Q: Consider a crank rocker mechanism with L1 = 90 mm, L2 = 180 mm, and L3 = 270 mm. The design…

A:

Q: mechanism like this one, if it is known the length of O2A (link 2) is 5 cm (link 3) is 4 cm (link 3)…

A:

Q: A 4-bar mechanism with all revolute pairs has link lengths ly=20 mm, lin = 40 mm, 1 = 50 mm and lout…

A: Given: The length of fixed link, Lf = 20 mm The length of input link, Lin = 20 mm The length of…

Q: 3. Calculate the torque and the rotation speed at the input pulley if the output pulley needs to…

A: (a) The torque at the input pulley is 66.67 lb•in. (b) The rotational speed of the input pulley is…

Q: solve/ show solution for given answer equations  kb = (Ab*Eb)/ g and kc = (Ac*Ec) / g   g- estimated…

A: I have attached the image below Explanation:

Q: What is the extreme transmission angle values by using maxima and minima condition, of the…

A: The extreme transmission angle in the four-bar mechanism is given as : μmin=sin-1cos2θ2 here ,…

Q: 3)Design a V – Belt drive to the following specifications Power transmitted = 75kw Speed of driving…

A:

Q: sin-D-d 20 V4C² - (D – d² D-d sin 20 Op

A:

Q: gn a hoist equipment using a reverted epicyclic gear train shown in 1. The drum must be keyed at the…

A:

Q: A 4 bar crank -rocker mechanism has the following configuration link 1=d=152.4mm link 2=a=50.8mm…

A: given data; for crank-rocker mechanism;

Q: A belt conveyor transports 18 tonnes per hr at 20°. Calculate the hp requirement to lift the load…

A:

Q: A hammer mill is driven by a High Torque (HT) AC motor. The system is used for 8 hours /day. Input…

A: Diameter of the motor shaft pulley = D1 = 1.33 cube root of Power / Speed max D1 = 1.33 cube root 25…

Q: Analyze the existing condition of the crank in a four- bar linkage. Draw a quick-return mechanism.…

A: A quick return mechanism is a device that generates a reciprocating motion in which the return…

Q: For the four-bar linkages below, indicate whether they are Grashof type 1 or 2 and whether they are…

A:

Q: A belt conveyor transports 18 tonnes per hr at 20°. Calculate the total length to be sufficient to…

A: V-belt pulleys (likewise called vee belt bundles) are gadgets which send power between axles by the…

Q: 1) Find the equivalent spring, N/mm 2) Find the force, F Kl: =7 K5. =11 k K2 =8 X=10 mm К3 -9 K4 =10…

A: GIVEN DATA - A SPRING SYSTEM GIVEN WE HAVE TO FIND BOTH POINT 1 & 2

Q: The shaft shown in the following figure is 200 mm long between self-aligning bearings at "A" and…

A:

Q: Tengins Given that p <q<r<s. Which of the

A: Given: p&lt;q&lt;r&lt;s

Q: For the Finishing Mill of a hot strip mill, the input shaft of several different gearboxes are each…

A: The objective of the question is to analyze the capabilities of a gearbox in a hot strip mill. This…

Q: Design a crank-rocker mechanism with a time ratio of Q = 1.34, throw angle of (θ4)MAX= 85°, and time…

A:

Q: llustrate a crank and slooted lever mechanism as an inversion of single slider crank chain. describe…

A: To describe : An expression for length of stroke in terms of link length. Concept used : A motor is…

Q: A shaft acting as simple supported beam is having a static deflection of 2.72 mm under a flywheel.…

A: As per given question  Deflections =2.72mm We have to find  critical speed in rad/sec

Q: The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an…

A: cross-sectional area A₁ = 820 mm². cross-sectional area  A₂ = 510 mm² For bronze alloy  E = 93 GPa…

Q: You have to select bearings which are used to support a shaft, bearings are mounted at each end of…

A: We can select type of bearing behalf of its maximum value of bending moment and twisting moment.…

Q: shaft. When the clutch is at rest, each shoe is pulled against a stop by a spring so as to leave a…

A: Centrifugal clutches generally consists of motor pulleys. Inside the rim of these pulleys, various…

Q: A chain drive is desired to couple a gearmotor with a bucket elevator. The 40 hp. gearmotor will…

A:

Q: 2. For a four bar crank rocker linkage, L1-34mm, L2-57mm, and L3=78mm. Find the actual range of…

A: According to the problem, the linkage is a crank-rocker linkage and crank rocker linkage occurs when…

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.