A shaft is loaded by a torque of 5 KN-m. The material has a yield point of 350 MPa. Find the required diameter using (a) Maximum shear stress theory (b) Maximum distortion energy theory Take a factor of safety of 2.5.

A shaft is loaded by a torque of 5 KN-m. The material has a yield point of 350 MPa. Find the required diameter using (a) Maximum shear stress theory (b) Maximum distortion energy theory Take a factor of safety of 2.5.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.8P: A tubular shaft being designed for use on a construction site must transmit 120 kW at 1,75 Hz, The...

See similar textbooks

Similar questions

Two designs for a shaft are being considered. Both have an outside diameter of 80 m and are 100 cm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque of T N. m. the missing Torque (T) = 199.
The coefficient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to 14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be transmitted. Q2 Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be takenas 1.5. Q3 a) An universal coupling is used to connect two mild steel shafts transmitting a torque of 6000 N- m. Assuming that the shafts are subjected to torsion only, find the diameter of the shaft and the pin. The allowableshear stresses for the shaft and pin may be taken as 55 MPa and 30 MPa respectively.
A winch raises a 60# bucket of paint, as shown. The main shaft of the winch is simply supported by bearings at A and C. The winch uses a 6"diameter pulley (B) and torque is applied at the end of the shaft to pull the cart. Determine the minimum shaft diameter based on the Distortion Energy (Von Mises) criterion using on a yield strength of 50ksi and a design factor of 2.0. 12" winch 18" C A Paint Rope
A shaft is transmitting 100 kW at 160 rpm. Find a suitable diameter for the shaft if the maximum torque transmitted exceed the mean by 25%. Take maximum allowable shear stress as 70 MPa.
Calculate diameter of shaft using maximum shear stress theory,when equivalent torque of 1000 x 103 N-mm acts on the shaft. 60 Mpa is the allowable shear stress for the shaft.
A Steel shaft is subjected to an end thrust producing a stress of 90 MPa and the minimum shearing stress on the surface arising from torsion is 60 MPa .The yield point stress of the material in simple tension was found to be 300 MPa. calculate the factor of safety of the shaft according to the following theory 1)maximum shear stress theory
a solid shaft is transmitting 1 mw at 240 rpm determine the daimeter of shaft exceed the mean of torque 20% take maximum shear alloy stress as 55mpa
Two designs for shaft are being considered. Both have an outside diameter of 60 mm and are 500 mm long. One is solid but the other is hallow with an inside diameter of 40 mm, both are made from steel ( G=80 GPa). Compare the torsional shear stress, and the mass of the two designs if they are subjected to a torque of 71 N.m.
Q1: A motor driving a solid circular steel shaft transmits 30 kW to a gear at B (as shown). The allowable shear stress in the steel is 40 MPa., G70 Gpa (a) What is the required diameter d of the shaft if it is operated at 1500 rpm? (b) What is the required diameter d if it is operated at 3000 rpm? (c) If the length of the shaft from the motor to the gear is 1 m, what are the angles of twist for the two speeds of rotation? Motor GIC G
A shaft made of steel receives 7.5 kW power at 1500 r.p.m. A pulley mounted on the shaft as shown in Fig. has ratio of belt tensions 4. The gear forces are as follows : F, = 1590 N; F, = 580 N Pulley Gear F1 A D F, -100 : 200- 100→ All dimensions in mm. Design the shaft diameter by maximum shear stress theory. The shaft material has the following properties : Ultimate tensile strength = 720 MPa; Yield strength = 380 MPa; Factor of safety = 1.5.
Parvinbhai
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa