A shaft ABCD, 25 mm in diameter is subjected to torques of 1850 N-m at B and 2000 N-m at C acting in the same direction. Segment AB is 4 m long, BC is 2 m long, and CD is 4 m long. Supports A and D are fixed and unyielding. G = 86 GPa. Determine the ff: A.) Reaction at A (N-m) B.) At what segment is the torsional stress largest? What is the stress on that segment? (MPa) C.) Angle of rotation between points A and C (radians)

A shaft ABCD, 25 mm in diameter is subjected to torques of 1850 N-m at B and 2000 N-m at C acting in the same direction. Segment AB is 4 m long, BC is 2 m long, and CD is 4 m long. Supports A and D are fixed and unyielding. G = 86 GPa. Determine the ff: A.) Reaction at A (N-m) B.) At what segment is the torsional stress largest? What is the stress on that segment? (MPa) C.) Angle of rotation between points A and C (radians)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.3.17P: A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and...

See similar textbooks

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
A stepped shaft ABC consisting of two solid, circular segments is subjected to torques T}and T2acting in opposite directions, as shown in the figure. The larger segment of the shaft has a diameter of dv- 2.25 in. and a length Lt= 30 in.; the smaller segment has a diameter d2— 1.75 in. and a length L, = 20 in. The torques are T, = 21,000 lb-in. and fz=10.000 lb-in. (a) Find reaction torque TAat support A. (b) Find the internal torque T(x) at two locations: x = L1/2 and x = L1+ L2/2. Show these internal torques on properly drawn free-body diagrams (FBDs).
A shaft ABCD, 25 mm in diameter is subjected to torques of 1850 N-m at B and 2000 N-m at C acting in the samedirection. Segment AB is 4 m long, BC is 2 m long, and CD is 4 m long. Supports A and D are fixed and unyielding.G = 86 GPa. A.) Reaction at A (N-m)B.) At what segment is the torsional stress largest? What is the stress on that segment? (MPa)C.) Angle of rotation between points A and C (radians)
F2. A circular shaft fabricated from steel is supported at each end by rigid constraints, as shown in the figure. The left side of the shaft is 2.5 in. in diameter and its right side is 2.00 in. in diameter. A torque of 900 ft-lb is applied at the center of the shaft where the diameter discontinuity is located. Determine the reactions at each of the supports. A B 2.50 in. Dia 12.00 in. Dia 60 in. Match each item to a choice: TORQUE (TB) TORQUE (TA) T = 900 ft-lb 60 in.
2. A shaft is designed to carry torque as shown below. The shaft consists of a steel rod which is fixed against rotation at both ends. In addition, the left half of the rod is well bonded to an aluminum sleeve. The assembly is loaded by a torque of 2000 N-m as shown. - The steel rod has shear modulus G = 80 GPa and radius r= 1.5 cm (hence polar moment of inertia Ip = 7.95 x 108 m². The aluminum sleeve has shear modulus G = 26 GPa, outer radius 2.6 cm and inner radius 1.5 cm (hence polar moment of inertia I, = 7.95 x 108 m²). 2000 N sleeve -0.57 rod a. Calculate the total reaction torques at the two walls (points A and C). b. Calculate the maximum shear stresses in the steel rod and the aluminum sleeve. c. Calculate the angle of twist at point B.
Determine the resisting torque at support A and B , of the shaft shown in the figure.
Q.1: A shaft composed of segments AB, BC is fixed between the two walls at 4 and C and loaded as shown in Figure below, For steel has a 25 mm circular cross section, shearing modulus G = 83 GPa. For aluminum has a 30 mm circular cross section, shearing modulus G - 28 GPa Determine: The two torques at supports A and C 2AN.m B. 3m 4m Steel aluninum Di-25mm Di-30mm G-83GPa G-28GP.
A bevel gear is attached to a shaft supported by self-aligning bearings at A and B and is driven by a motor. The axial force, radial force, and tangential force are known. Assume the weight of the gear and shaft is negligible and that the bearing at A takes all the thrust load A) Draw (to scale) axial load, shaft torque, shear force(x-y and x-z), and bending moment(x-y and x-z)diagrams for the shaft B)Determine the values of axial load and torque along the shaft
1. The shaft assembly shown below is fixed at its ends A and D. It consists of an aluminum (G = 30 GPa) segment AB rigidly connected to a steel (G= 75 GPa) segment BCD. Both segments have a 80-mm diameter. If the shaft is subjected to a torque 7 of 9 kN-m applied at C, determine The reactions at A and D; a) b) The angle of twist at point B; The maximum shear stress in the shaft. 300 mm -Aluminum 600 mm Steel C 300 mm
Problem 2. Each segment of bar ABC has length L. and shear modulus G and both segments have solid circular cross sections. Torque per unit length t(x) is applied between points B and C. The diameter of segment AB varies linearly from 2d at point A to d at point B. In terms of the given quantities, a) Find the torques at A and C. b) Find the twist angle os at point B. G 2d A -L d B G *(x) = to (²=²) ² C to x
The shaft, is driven by pulley B from an electric motor. Another belt drivefrom pulley A is running a compressor. The belt tensions for pulley A are 1500 N and 600 N. The ratioof belt tensions for pulley B is 3.5. The diameter of pulley A is 150 mm and the diameter of pulley B is 480 mm. The allowable tensilestress for the shaft material is 170 MPa and the allowable shear stress is 85 MPa. Taking torsion andbending factors as 1.25 and 1.75 respectively, find the shaft diameter.Also find out the dimensions for a hollow shaft with outside diameter limited to 30 mm. Compare theweights of the two shafts. [Ans. 30 mm ; 24 mm ; 1.82 Given Length CD=350mm Length AB=150mm Length BD=100mm The total length is CD =350
A steel stepped shaft ABCD fixed at A is subjected to three torques at points B, C and D, with magnitudes T₁ = 40 kip-in, T₂ = 50 kip-in and Ts= 30 kip-in and directions as shown in Figure 1.1. The segments AB and BC are solid with diameters dx = 3 in and dec = 2 in respectively, while segment CD is hollow with an outer diameter dan 1.5 in and a wall thickness of 0.25 in. The shear modulus of elasticity is equal to G=11.6x10³ ksl. T₁ T₂ 4 = 20 in A B L₂ = 20 in Figure 1.1 a) Draw the torsion moment diagram for the shaft and calculate how long should segment CD be so that the angle of twist between points B and D is equal to zero. T₁ 4₂-25 in b) If Ts is dropped, a fixed support is added at point D (as shown in Figure 1.2) and the length of segment CD is equal to 15 in, find the support reactions at points A and D and the maximum shear stress developed in segment BC. The magnitudes of the torques at points B and Care the same as in part a). B C L₂= 25 in T₂ * Figure 1.2 Hollow C Hollow…