A bevel gear is attached to a shaft supported by self-aligning bearings at A and B and is driven by a motor. The axial force, radial force, and tangential force are known. Assume the weight of the gear and shaft is negligible and that the bearing at A takes all the thrust load A) Draw (to scale) axial load, shaft torque, shear force(x-y and x-z), and bending moment(x-y and x-z)diagrams for the shaft B)Determine the values of axial load and torque along the shaft

Q: 13. For the same Figure in Problem 11, the reaction at the fixed support B is- a. 645 N-m (CW) b.…

A: Torque given are 800 Nm and 500 Nm. Diameter of the shaft, d= 20 mm= 0.02 m

Q: Problem #1. The 60-mm diameter shaft is subjected to torques as shown. If the applied allowable…

A:

Q: B TB = 90 N-m fr 200 mm b) + 200 mm с Tc = 30 N-m + 400 mm D D₂ Side view of a shaft The side view…

A: According to the given data LAB=LBC=200mm , D1=30mm LCD=400mm , D2=50mm G=40 GPa TB=90 N.m TC=30 N.m…

Q: Figure 2 shows a solid shaft consisting of two prismatic circular parts in equilibrium under the…

A:

Q: (a) The tubular rotor shaft of a wind turbine shown in Figure 3(a) is of 50 mm and 40 mm outer and…

A: Given data Outer Diameter of Tubular shaft = Do = 50 mm = 0.05 mInner Diameter of Tubular Shaft = Di…

Q: Determine the angle of rotation at the free end.

A: Given: To determine: The angle of rotation at the free end due to the torque applied

Q: A torsional bar is subjected to two external torques (10Nm and 5Nm) and a distributed torque…

A: according to the details given above

Q: 2- The motor in the figure applies 50 Nm torsion (torque) to the AB shaft. This torque is…

A:

Q: Problem 5-13: The shaft has an outer diameter of 100 mm and an inner diameter of 80 mm. If it is…

A:

Q: A steel cable is supporting a load of F = 9800 lb and is wrapped around a drum attached to gear A as…

A:

Q: Calculate the amount of torque generated by the rod with circular cross-section as shown in the…

A: Given: Force = 48 lb Diameter = 5 in.

Q: The end gear (closest to the journal bearing at A) is subjected to the loading shown in the figure.…

A: Given: The yields strength of material = 80 MPa

Q: The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and…

A:

Q: The figure shows a shaft carrying three gears that rotates at 1150 rpm. Gear A delivers power =10kw…

A: Given, Gear A deliver 10KN Gear C deliver 15KN A shaft carrying 3 gears that rotates at 1150 rpm…

Q: 25m (a) The tubular rotor shaft of a wind turbine shown in Figure 3(a) is of 50 mm and 40 mm outer…

A: Given data:- Inner diameter = 40 mm Outer diameter = 50 mm Torque = 2.5 kN-m Moment = 3.6 kN-m Find…

Q: 1. A solid steel shaft ABCDE having diameter d = 40 mm turns with a constant angular velocity and…

A: For the solution refer below images.

Q: The shaft shown in Figure 4 is loaded with concentrated torques at B, C, and D, and is fixed at A.…

A:

Q: The bending stress at point A.

A: Given data Outer Diameter of Shaft = Do = 50 mm = 0.05 mInner Diameter of Shaft = Di = 40 mm = 0.04…

Q: The shaft is fixed at ends A and B and has a positive torque T a distance of 4m from A and 8m from…

A:

Q: A circular shaft of the dimensions shown in the following figure is subjected to three torques : T1…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.