Answered: A selector switch and two - wire pilot…

A selector switch and two - wire pilot device cannot be used to control a large motor directly but rather must be connected to a magnetic starter. Why this is true.?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter24: Time-delay, Low-voltage Release Relay

Section: Chapter Questions

Problem 2SQ

See similar textbooks

Related questions

Q: 22/ What is the armature current value of the DC motor at starting of the Motor? a. less than 10…

A: To start a dc motor we need high current. As initally the volatge is very small in dc motor.

Q: Explain any one type of enclosure used in DC motors with necessary diagram

A: Electrical machines can be either generator , transformers or motors. They can be either Ac machines…

Q: 1. When is the counter EMF at a minimum?

Q: Rotor eccentricity can be caused by A. high motor loads. B. excessive voltage. C. poor motor…

A: A rotor eccentricity is a condition of unequal air gap that exists between the stator and the rotor.…

Q: Why the rotor conductors of the squirrel cage rotor are short-circuited and in the case of slip-ring…

Q: X1. The magnetic strength of the field poles on a permanent magnet DC motor cannot be varied. a)…

A: X1) True, because the magnetic strength of the field in permanent dc motor is fixed. X2) The speed…

Q: If the starter resistance is 1.9 ohms, what current does the motor take at the instant of starting…

A: At starting back emf is zero. So armature current at starting =( terminal voltage- brush voltage…

Q: Please answer all subparts please answer in typing format

A: Step 1: Step 2: Step 3: Step 4:

Q: 4) Is the statement “An induction motor has the same physical stator as a synchronous machine, with…

A: Induction motor is single excited machine.synchronous motor is a doubly excited machine.Rotor of…

Q: How does the starting torque responsible in the use of the starter for the 3 phase induction motor

A: In the 3 phase induction motor, the value of the armature resistance is kept minimum to avoid the…

Q: Rotor slots are often skewed to help reduce A. starting current. B. rotor heat. C. starting torque.…

A: Given: Skewed rotors slots

Q: Overhauling is a condition in which the motor’s armature rotates (…

A: The explanation is as follows.

Concept explainers

Speed control of motor

Speed control by DC motor-speed controller is required to realize variable speed drive. Whenever a motor drives a particular load, it is called drive, and variable speed drive refers to a load requiring variable speed. All this is obtained by a DC motor speed controller.

Question

A selector switch and two - wire pilot device cannot be used to control a large motor directly but rather must be connected to a magnetic starter. Why this is true.?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

6.a. When you're taking a PM motor apart you should exercise special care not to damage theA. end bells.B. commutator.C. permanent magnets.D. brush holders.6.b. A PM field servo motor may be equipped with a resolver that is used toA. excite the armature windings.B. create a voltage that increases with velocity.C. prevent the brushes from sparking.D. feed back position information.
2. Draw the schematic diagram of a six point Drum Switches that operate the long shunt compound dc motor in reverse –forward operation. Connect all the parts into the Drum Switch terminals only not in the outside of the Drum Switches. Explain your connection.
Electrical engineering subject of electrical machines/ I need a correct and accurate solution
21. A PM field servo motor may be equipped with a resolver that is used to A. prevent the brushes from sparking. B. create a voltage that increases with velocity. C. excite the armature windings. D. feed back position information.
Rotor eccentricity can be caused by A. high motor loads.B. excessive voltage.C. poor motor mounting. D. loose stator coils.
7. There are two wires labeled P1 and P2 at a DC motor's junction box. These wires will attach to whatinternal component of the motor?A. A speed potentiometerB. GroundC. A thermostat
Draw the circuit please.
A 4–pole, 500 V d.c. shunt motor has 720 wave–connected conductors on its armature. The full–load armature current is 60 A and the flux per pole 0.03 Wb. The armature resistacne is 1.2 Ω. What is the full–load speed of the motor?
22/ What is the armature current value of the DC motor at starting of the Motor? a. less than 10 A b. zero c. Rated current d. High current
Which one of the following motor types uses permanent magnets in the armature or rotor? A. PM servo motorB. PM motorC. Pancake motor D. Stepper motor
A three-terminal manual starting rheostat has a resistance of 5.2 ohms in its starting resistor. The holding coil resistance is 10 ohms. This starting rheostat is connected to a shunt motor. The resistance of the armature is 0.22 ohm; the resistance of the shunt field is 100 ohms. The line voltage is 220VDC. a. What is the starting surge current taken by the motor? b. What is the current in the holding coil with the moveablew arm in the run position? c. What is the CEMF with the movable arm in the on position if the armature current is 20 amps?
5. A shunt motor operates at a flux of 25 mWb per pole, is lap wound and has 2 poles and 360 conductors. The armature resistance is 0.12 ohm and the motor is designed to operate at 115 volts, taking 60 A in armature current at full load. The external resistance inserted in the armature circuit so that the armature current shall not exceed twice its full load value at starting. When the motor has reached a speed of 400 rpm, the external resistance is cut by 50%, what is the armature current, at this speed. A. 102A B. 167A I C. 213 A D. 184A