1. When is the counter EMF at a minimum?When the field current is at a maximumWhen the motor armature is not rotatingWhen the current applied to the motor is at fullload.When the motor current is at a minimum

Answered: Image /qna-images/answer/0f0716eb-28c6-42ff-9394-25f8bac776db.jpg

Answered: 1. When is the counter EMF at a…

Engineering

Electrical Engineering

1. When is the counter EMF at a minimum?

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter43: About Dc Motors

Section: Chapter Questions

Problem 1SQ

See similar textbooks

Related questions

Q: 9. The amount of current that will operate an overcurrent protective device is inversely…

A: The over current protection (let us consider a fuse) operates on the heat development due to the…

Q: Explain and elaborate the difference between zener and avalanche breakdown voltage

A: The zener breakdown and avalanche breakdown voltage of the zener diode need to be briefed.

Q: Describe the primary components of a typical power system.

A: A typical power system, which includes the generation, transmission, and distribution of electrical…

Q: 6. The discharge curves shown are typical of which components? (a) Capacitors (b) Inductors (c)…

A: The type of device which exhibits the given graph needs to be identified. Two different plots are…

Q: Which microelectronic device failure mode is the most important for systems which must operate for…

A: In this case, the reason, which causes microelectronic devices to fail, needs to be selected.

Q: If 3-phase transfomer configuration in figure in has the givens as listed below: E-line on high…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: What considerations are vital for integrating IoT in safety-critical environments, such as nuclear…

A: We have to discuss about considerations that are vital for integrating IoT in safety-critical…

Concept explainers

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.

Question

1. When is the counter EMF at a minimum?
When the field current is at a maximum
When the motor armature is not rotating
When the current applied to the motor is at full
load.
When the motor current is at a minimum

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Answer please in 10 minutes
With aid of a diagrams explain how the starter of a DC motor works
I need that quesitons answer also rpm is 1000 and the rate is %10 on red texting
A 150 HP, 3-phase, 6 pole, 460 V, 60 Hz induction motor draws 195 A line current at full load speed of 1170 rpm and 0.85 pf. Solve for the percent slip at full load. (a). 2.5% (b). 3.0% (c). 2.8% (d). 2.0%
A 220 V shunt motor driving its normal load draws an armature current of 50 A from a 220 V dc source. The armature resistance of this motor including brushes is 0.25 ohms. How much armature current (minimum) Will this motor draw from a 200 V DC source when driving the same load with the field adjusted to maintain the same speed.
A 4-pole, 650v shunt motor has 720 wave connected conductors on its armature, The full-load armature current is 80A and the line flux per pole is 0,04Wb. The armature resistance is 0.4 ohms. Calculate the full load speed. Select the correct response: 548.80 rpm 321,88 rpm 643.75 грm 344.86 грm
9) If the series motor loss its load suddenly, then A. its torque goes too high B. its speed decreased to zero C. its torque decreased to zero D. its speed goes too high
J1. What are the standard identification letters for the shunt field winding of a DC compound motor? a) A1 and A2 b) S1 and S2 C) F1 and F2 d) none of the above J2. The commutating field is another term for interpoles. a) true b) false J3. What are the standard identification letters for the commutating field winding of a DC compound motor? a) C1 and C2 b) S3 and S4 c) either "a" or "b" d) neither "a" nor "b"
An increase in the torque angle a results in: O A. No change in the induced torque O B. Decreasing the induced torque O C. Decreasing the load on the synchronous motor D. None of the other choices are correct O E. Increasing the induced totque
K-1)The speed of a 3-phase wound-rotor induction motor can be changed by varying the amount of resistance in the rotor circuit. a) true b) false K-2). Which of the following statements are true about a 3-phase synchronous motor? a) It is a constant speed motor even under varying loads. b) It runs at the same speed the magnetic field rotates on the stator. c) It can correct its own, and the supply line's power factor d) all of the above K-3. A) What determines the speed of a 3-phase synchronous motor? a) the number of poles b) the frequency of the supply c) both "a" and "b" d) neither "a" nor "b" K-3)B) From a technician's standpoint, which of the following is the most practical method of providing a wide range of speed control for a 3-phase synchronous motor? a) by changing the frequency b) by changing the number of poles c) both "a" and "b" d) neither "a" nor "b"
14/ What are the following statements are true for a three-phase induction motor? I. Three-phase induction motor stator winding is fed from a three-phase supply II. Stator carries a three-phase winding III. Rotor carries a short circuited winding a. I and II only b. I,II and III c. II and III d. I only
A three-phase, six-pole, 60 Hz, 230-volt wound rotor motor has its stator connected in delta and its rotor in star. There are 70 percent as many rotor conductors as stator conductors as stator conductors. Calculate the voltage and frequency between slip rings if normal voltage is applied to the stator when, a, the rotor is at rest, b. the rotor slip is 0.04