A sector gate of radius 3 m and length 4 m retains water as shown in thefigure below. Determine the magnitude and direction of the resultant force dueto the water acting on the gate Document3 - WordSign inO XFileHomeInsertDesignLayoutReferencesMailingsReviewViewHelpO Tell me what you want to do2 ShareX CutCalibri (Body)E- E- EE TP Find -- A AAa -AaBbCcDc AaBbccDc AaBbC AaBbCcC AaB AaBbCcC- ||11ED Copyab. ReplaceA SelectBIU v abE x, x'PasteA v aly - AI NormalT No Spac. Heading 1 Heading 2TitleSubtitleFormat PainterClipboardFontParagraphStylesEditing346.71= 3 mHinge60°Page 1 of 1O words+ 290%vervolg op rugkanCV09:29 AM.ll E ) O01/06/2021

Horizontal Force on Gate : Vertical Force on Gate :

Answered: A sector gate of radius 3 m and length…

A sector gate of radius 3 m and length 4 m retains water as shown in the figure below. Determine the magnitude and direction of the resultant force due to the water acting on the gate

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. The'rectangular gate AB is 3.05 m x 1.22 m in dimension and its pin connected at the point B. If the surface on which the gate rests at A is frictionless, what is the reaction at A? i 2m B 3.05 x 1.22 gate 30 A
Determine the vertical component of the total hydrostatic force (kN) acting on the curved surface. The fluid in the 3.11 m long gate is water. a=7.8 m b=2.4 m r3m
An equivalent force-couple system: Three forces F1 = 100 N, F2 = 50 N, and F3 = 30 N act on a structure as shown in the figure where α = 30o, θ = 60o, L = 1 m and h = 0.5 m. Find the equivalent force-couple system about point D.
determine the support reactions at point A,B & C. TAKE NOTE: The support C is fixed and Support B is an internal hinge. Kindly show your complete solutions.refer to the given figure below.
I need the answer as soon as possible
answer it with only solution
The electric power transmission tower supports two wires that apply 18 kN verticalforces, and the 36 kN horizontal force crudely models wind loading during astorm. Assume that the supports in A and B are hinge support and roller support,respectively. Solve for support reactions.
Example Determine the horizontal and vertical components of force at pins B and C. The suspended cylinder has a mass of 75 kg. 0.3 m 75*(9.81) 0.3 m Cx D,= 4951 D,= FAB 1.5 m 1.5 m Cy 75 (9.81) 0.9m 2 m 2 m 0.5 m 0.5 m 0.3 m
Gate AB retains water as shown in the figure. The gate is supported every 2 m (perpendicular to the plane of view) by member BC, which is attached to a 2000 kg mass at point C. What minimum static coefficient of friction μs, along the contact surface between the mass and its base, is needed for the gatestructure to be in equilibrium? There are pins at points A, B, andC.
Q4- A rectangular gate 6 ft tall and 5 ft wide in the side of an open tank is held in place by the force F as indicated in Figure. The weight of the gate is negligible, and the hinge at O is frictionless. (a) Determine the water depth, h, if the resultant hydrostatic force of the water acts 2.5 ft above the bottom of the gate, i.e., it is collinear with the applied force F. (b) For the depth of part (a), determine the magnitude of the resultant hydrostatic force. (c) Determine the force that the hinge puts on the gate under the above conditions. Water Hinge 0 h Gate F 6 ft 2.5 ft
Determine the magnitude of the horizontal and vertical components of the total force per meter length acting on the three-quarter cylinder gate shown.
The rectangular (0.6mx0.9m) sluice AB blocks liquid with a specific gravity of 0.79. The sluice door weighs 300N and finds the force that must act on the cable BCD to open the sluice door.